Mitsubishi Electric PRH-P10MYA Technical & Service Manual Download Page 63

Page: 63 / 87

[9] Self-diagnosis and troubleshooting

Abnormal-
ity display

None

Meaning of abnormality display and
abnormality troubleshooting

Indoor/outdoor connection erro-
neous wiring

1. Outdoor-side controller board

automatically recognizes the
number of connected indoor-side
unit. However, when the number of

connected indoor unit cannot be
set due to erroneous indoor/
outdoor connection, erroneous

wiring, etc. even after 4 minutes

have elapsed since the power
was turned on, an abnormality
is recognized.

Indoor/outdoor connection erro-
neous wiring

Outdoor-side controller board
automatically sets the unit No. of
the indoor unit. However, when

the unit No. of the indoor-side unit
cannot be set due to indoor/outdoor
connection erroneous wiring even

after 4 minutes has elapsed since

the power was turned on, an
abnormality is recognized.

Start-up time over

When start-up processing does not
end even through 4 minutes has
elapsed since the power was turned
on, an abnormality is recognized.

Reverse phase detected

Cause

(1) Voltage not applied to unit terminal

block TB1.

a. Power supply circuit breaker not

closed.

b. Power supply terminals connection

faulty, or disconnected.

c. Missing phase

(2) No electricity at outdoor-side controller

board power supply connector.

a. Power supply connector contact

faulty.

b. Terminal CN20 on outdoor-side

controller board disconnected.

(3) Outdoor-side

(4) Transformer faulty

controller board faulty.

a. Blown fuse on outdoor-side

controller board.

b. Part faulty.

(1) Indoor/outdoor connection wire con-

tact faulty.

(2) Outdoor-side controller board send/

receive circuit faulty.

(3) Indoor-side controller board send/

receive circuit faulty.

(4) Noise has entered on power supply

or indoor-side/outdoor-side
controller board connection wire.

(1) Indoor/outdoor connection wire con-

tact faulty.

(2) Outdoor-side controller board send/

receive circuit faulty.

(3) Indoor-side controller board send/

receive circuit faulty.

(4) Noise has entered on power supply

or indoor-side/outdoor-side
controller board connection wire.

(1)

(2)

Indoor-side/outdoor-side controller
board connection wire contact faulty.

(2) Noise has entered on power supply

or indoor-side/outdoor-side
controller board connection wire.

Power supply reverse phase

connection.

Power supply missing phase.

Judgment method and remedy

(1)a. Check power supply circuit breaker

b. Check power supply terminal block

connections.

c. Check power supply terminal block

connections.

(2)a. Check power supply connector board

connections.

(3)a. Replace fuse.

b. Replace controller board.

(However, when cannot be repaired
even through the check above was
carried out.)

(1) Check

(4) Replace transformer

if indoor/outdoor connection

wire disconnected or loose. Also
check polarity.

(2) Check by turning power off and on.

If abnormality is displayed again, re-
place outdoor-side controller board or
indoor-side controller board.

LED3 of the indoor-side controller
board flashes when communication

is being performed.

(1) Check power supply terminal block

connections.

(2) Replace outdoor-side controller board

(However, when cannot be repaired

even though check above was carried

out.)

- 60 -

Summary of Contents for PRH-P10MYA
























































































Search results

Summary of Contents for PRH-P10MYA

Reviews:

Related manuals for PRH-P10MYA

Brands by name

Popular brands

Mitsubishi Electric PRH-P10MYA, Technical & Service Manual

Search results

Summary of Contents for PRH-P10MYA

Reviews:

Related manuals for PRH-P10MYA

Brands by name

Popular brands