13
8. Electrical work
Perform wiring as shown in the diagram to the lower left. (Procure the cable
locally.)
Make sure to use cables of the correct polarity only.
[Fig. 8-2-5] (P.6)
Connect the terminal blocks as shown in the diagram below.
Caution:
Use care not to make mis-wiring.
Firmly tighten the terminal screws to prevent them from loosening.
After tightening, pull the wires lightly to confirm that they do not move.
8.3. Remote controller
8.3.1. For wired remote controller
1) Two wired remote controllers setting
If two wired remote controllers are connected, set one to Main and the other to
Sub. For setting procedures, refer to Function selection of remote controller in the
operation manual for the indoor unit.
8.3.2. For IR wireless remote controller
1) Installation area
Area in which the IR wireless remote controller is not exposed to direct
sunshine.
Area in which there is no near by heating source.
Area in which the IR wireless remote controller is not exposed to cold (or hot)
winds.
Area in which the IR wireless remote controller can be operated easily.
Area in which the IR wireless remote controller is beyond the reach of children.
* The signal can travel up to approximately 7 meters [23 ft] (in a streight line) within
45 degrees to both right and left of the center line of the receiver.
2) Setting the Model No.
[Fig. 8-3-1] (P.6)
8.4. Function settings
8.4.1. Function setting on the unit (Selecting the unit functions)
1) For wired remote controller [Fig. 8-4-1] (P.7)
1. Changing the external static pressure setting.
Be sure to change the external static pressure setting depending on the duct and
the grill used.
1
Go to the function setting mode.
2
Use the
C
button to set the refrigerant address (
III
) to 00.
3
Press
D
and [--] will start to flash in the unit number (
IV
) display.
4
Use the
C
button to set the unit number (
IV
) to 01-04 or AL.
5
Press the
E
MODE button to designate the refrigerant address/unit number.
[--] will flash in the mode number (
I
) display momentarily.
6
Press the
F
buttons to set the mode number (
I
) to 08.
7
Press the
G
button and the current set setting number (
II
) will flash.
Use the
F
button to switch the setting number in response to the external static
pressure to be used.
8
Press the MODE button
E
and mode and the setting number (
I
) and (
II
) will
change to being on constantly and the contents of the setting can be confirmed.
9
Press the FILTER
A
and TEST RUN
B
buttons simultaneously for at least two
seconds. The function selection screen will disappear momentarily and the air
conditioner OFF display will appear.
0
To set the static pressure at 70,100,150Pa [0.28, 0.40, 0.60 in. WG], repeat steps
3
to
9
. (Set the mode number to 10 for step
6
.)
2. Other functions
1
Select unit number 00 for the settings. (Settings for all indoor units)
Refer to Function table 1.
2
Select unit number 01 to 04 or AL for the settings. (Settings for each indoor unit)
To set the indoor unit in the individual system, select unit number 01.
To set each indoor unit of two, three or four indoor units, which are connected
when these units are simultaneously in operation, select unit number 01 to 04.
To set all indoor units of two, three or four indoor units which are connected when
these units are simultaneously in operation, select AL.
Refer to Function table 2.
2) For IR wireless remote controller [Fig. 8-4-2] (P.7)
1. Changing the external static pressure setting.
Be sure to change the external static pressure setting depending on the duct and
the grill used.
1
Go to the function select mode
Press the CHECK button
F
twice continuously.
(Start this operation from the status of remote controller display turned off.)
is lighted and 00 blinks.
Press the TEMP button
C
once to set 50. Direct the wireless remote controller
toward the receiver of the indoor unit and press the Hour button
A
.
2
Setting the unit number
Press the TEMP button
C
and
D
to set the unit number to 01-04 or AL. Direct the
wireless remote controller toward the receiver of the indoor unit and press the
Minute button
B
.
3
Selecting a mode
Enter 08 to change the external static pressure setting using the
C
and
D
buttons.
Direct the wireless remote controller toward the receiver of the indoor unit and
press the Hour button
A
.
Current setting number:
1 = 1 beep (one second)
2 = 2 beeps (one second each)
3 = 3 beeps (one second each)
4
Selecting the setting number
Use the
C
and
D
buttons to change the external static pressure setting to be
used.
Direct the wireless remote controller toward the sensor of the indoor unit and
press the Hour button
A
.
5
To set the external static pressure
Repeat steps
3
and
4
to set the mode number to 10.
6
Complete function selection
Direct the wireless remote controller toward the sensor of the indoor unit and
press the ON/OFF button
E
.
Note:
Whenever changes are made to the function settings after installation or
main-tenance, be sure to record the changes with a mark in the Setting
column of the Function table.
3) Changing the power voltage setting (Function table 1)
Be sure to change the power voltage setting depending on the voltage used.
A
Indoor terminal block
B
Earth wire (green/yellow)
C
Indoor/outdoor unit connecting wire 3-core 1.5 mm
2
[AWG 16] or more
D
Outdoor terminal block
1
Connecting cable
Cable 3-core 1.5 mm
2
[AWG 16], in conformity with Design 245 IEC 57.
2
Indoor terminal block
3
Outdoor terminal block
4
Always install an earth wire (1-core 1.5 mm
2
[AWG 16]) longer than other cables
5
Wired remote controller cable
Wire No
size (mm
2
) : Cable 2C
0.3
This wire accessory of remote controller
(wire length : 10 m [32 ft], non-polar. Max. 500 m [1640 ft])
6
Wired remote controller
1
Insert batteries.
2
Press the SET button with something sharp at the end.
Start this operation from the status of IR wireless remote controller display
turned off.
blinks and Model No. is lighted.
3
Press the temp
button to set the Model No.
4
Press the SET button with something sharp at the end.
and Model No. are lighted for three seconds, then turned off.
Indoor Unit Model
A
Model No.
PEAD
026
Switch OFF the remote controller.
Press the
A
and
B
buttons simultaneously and hold them for at least 2
seconds. FUNCTION will start to flash.
MODEL SELECT
MODEL SELECT
External static pressure
Setting no. of mode
no. 08
Setting no. of mode
no. 10
35 Pa [0.14 in. WG]
2
1
50 Pa [0.20 in. WG] (before shipment)
3
1
70 Pa [0.28 in. WG]
1
2
100 Pa [0.40 in. WG]
2
2
150 Pa [0.60 in. WG]
3
2
CHECK
KD79P399H01.book Page 13 Tuesday, July 1, 2014 4:51 PM
