Mitsubishi Electric MSY-GL-NA Series Service Manual Download Page 71

Page: 71 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

4. Removing the discharge temperature thermistor,

defrost thermistor (MUZ), outdoor heat exchanger

temperature thermistor and ambient temperature

thermistor

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the lead wire to the reactor and the following

connectors:

CN641 (Defrost thermistor (

MUZ

) and discharge tempera-

ture thermistor)

CN643 (Ambient temperature thermistor)

CN644 (Outdoor heat exchanger temperature thermistor)

(3) Pull out the discharge temperature thermistor from its holder.

(4) Pull out the defrost thermistor from its holder.

(5) Pull out the outdoor heat exchanger temperature thermistor

from its holder.

(6) Pull out the ambient temperature thermistor from its holder.

Photo 8

Photo 9

Photo 10

5. Removing outdoor fan motor

(1) Remove the top panel, cabinet and service panel. (Refer to

section 1.)

(2) Disconnect the following connectors:

CN931 and CN932 (Fan motor)

(3) Remove the propeller fan nut.

(4) Remove the propeller fan.

(5) Remove the screws fixing the fan motor.

(6) Remove the fan motor.

NOTE

: The propeller fan nut is a reverse thread.

6. Removing the compressor and 4-way valve

(1) Remove the top panel, cabinet and service panel. (Refer to

section 1.)

(2) Remove the back panel. (Refer to section 1.)

(3) Remove the inverter assembly. (Refer to section 2.)

(4) Recover gas from the refrigerant circuit.

NOTE:

Recover gas from the pipes until the pressure gauge

shows 0 PSIG.

(5) Detach the brazed part of the suction and the discharge

pipe connected with compressor.

(6) Remove the compressor nuts.

(7) Remove the compressor.

(8) Detach the brazed part of 4-way valve and pipe. (Photo 7)

Screws of the

outdoor fan motor

Brazed part of the

discharge pipe

Brazed part of the suction pipe

Discharge temperature

thermistor

Outdoor heat

exchanger tempera-

ture thermistor

Ambient tem-

perature

thermistor

Defrost thermistor (

MUZ

)

Propeller fan nut

OBH733J

Summary of Contents for MSY-GL-NA Series













































































Search results

Summary of Contents for MSY-GL-NA Series

Reviews:

Related manuals for MSY-GL-NA Series

Brands by name

Popular brands

Mitsubishi Electric MSY-GL-NA Series, Service Manual

Search results

Summary of Contents for MSY-GL-NA Series

Reviews:

Related manuals for MSY-GL-NA Series

Brands by name

Popular brands