Mitsubishi Electric MSY-GL-NA Series Service Manual Download Page 52

Page: 52 / 76

H Check of R.V. coil

MUZ-GL09/12/15/18NA MUZ-GL09/12/15/18NAH

(MUZ)

MUZ-GL24NA MUZ-GL24NAH

* First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 10-4.

* In case CN721 is disconnected or R.V. coil is open, voltage is generated between the terminal pins of the connector

although no signal is being transmitted to R.V. coil.

Check if CN721 is connected.

Is there 208/230 V AC between CN721

and on the inverter P.C. board

3 minutes after the power supply is turned

ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates in COOL mode even if it is set to HEAT mode.

Is there 208/230 V AC between CN721

and on the inverter P.C. board

3 minutes after the power supply is turned

ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates in HEAT mode even if it is set to COOL mode.

Disconnect connector between the

compressor and the power module

(IC700).

Turn ON the power supply and press

EMERGENCY OPERATION switch

twice (HEAT mode).

Disconnect connector between the

compressor and the power module

(IC700).

Turn ON the power supply and

press EMERGENCY OPERATION

switch once (COOL mode).

* First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 10-4.

* In case CN602 is disconnected or R.V. coil is open, voltage is generated between the terminal pins of the connector

although no signal is being transmitted to R.V. coil.

Check if CN602 is connected.

Is there 208/230 V AC between CN602

and on the inverter P.C. board

3 minutes after the power supply is turned

ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates in COOL mode even if it is set to HEAT mode.

Is there 208/230 V AC between CN602

and on the inverter P.C. board

3 minutes after the power supply is turned

ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates in HEAT mode even if it is set to COOL mode.

Disconnect connector between the

compressor and the IGBT module

(IC700).

Turn ON the power supply and press

EMERGENCY OPERATION switch

twice (HEAT mode).

Disconnect connector between the

compressor and the IGBT module

(IC700).

Turn ON the power supply and

press EMERGENCY OPERATION

switch once (COOL mode).

OBH733J

Summary of Contents for MSY-GL-NA Series













































































Search results

Summary of Contents for MSY-GL-NA Series

Reviews:

Related manuals for MSY-GL-NA Series

Brands by name

Popular brands

Mitsubishi Electric MSY-GL-NA Series, Service Manual

Search results

Summary of Contents for MSY-GL-NA Series

Reviews:

Related manuals for MSY-GL-NA Series

Brands by name

Popular brands