background image

11

7. Trouble Shooting

Having trouble?

Here is the solution. (Unit is operating normally.)

Noise is louder than specifications.

 

The indoor operation sound level is affected by the acoustics of the 

particular room as shown in the following table and will be higher than 

the noise specification, which was measured in an echo-free room.

High sound-

absorbing 

rooms

Normal rooms

Low sound-

absorbing 

rooms

Location 

examples

Broadcasting 

studio, music 

room, etc.

Reception 

room, hotel 

lobby, etc.

Office, hotel 

room

Noise levels

3 to 7 dB

6 to 10 dB

9 to 13 dB

Nothing appears in the wireless remote controller display, the display 

is faint, or signals are not received by the indoor unit unless the remote 

controller is close.

 

The batteries are low.

 

Replace the batteries and press the Reset button.

 

If nothing appears even after the batteries are replaced, make sure that 

the batteries are installed in the correct directions (+, –).

The operation lamp near the receiver for the wireless remote controller 

on the indoor unit is flashing.

 

The self diagnosis function has operated to protect the air conditioner.

 

Do not attempt to repair this equipment by yourself.

 

Turn off the power switch immediately and consult your dealer. Be sure 

to provide the dealer with the model name.

The wireless remote controller does not operate (the indoor unit beeps 

4 times).

 

Switch the auto mode setting to the AUTO (single set point) mode or 

AUTO (dual set point) mode. For details, refer to the included Notice (A5 

sheet) or the Installation Manual.

8. Specifications

Item 

Model

PEAD-M50JAA(D)

PEAD-M60JAA(D)

PEAD-M71JAA(D)

PEAD-M100JAA(D)

Power source

220-240 V (50/60 Hz)

Dimension

Height

mm

250

Width

mm

900

1100

1400

Depth

mm

732

Net weight*

2

kg

26(27)

29(30)

38(39)

Fan

Airflow rate (Low-Middle-High)

m

3

/min

12.0-14.5-17.0

14.5-18.0-21.0

17.5-21.0-25.0

24.0-29.0-34.0

External static pressure*

3

Pa

35/50/70/100/125

35/50/70/100/125

35/50/70/100/125

35/50/70/100/125

Sound level (Low-Mid-High)*

4

dB(A)

30-35-39

30-33-37

30-34-39

33-38-42

Filter

Standard filter

Item 

Model

PEAD-M125JAA(D)

PEAD-M140JAA(D)

Power source

220-240 V (50/60 Hz)

Dimension

Height

mm

250

Width

mm

1400

1600

Depth

mm

732

Net weight*

2

kg

39(40)

43(44)

Fan

Airflow rate (Low-Middle-High)

m

3

/min

29.5-35.5-42.0

32.0-39.0-46.0

External static pressure*

3

Pa

35/50/70/100/125

35/50/70/100/125

Sound level (Low-Mid-High)*

4

dB(A)

36-40-44

40-44-49

Filter

Standard filter

Notes:

*   Operation temperature of indoor unit.

 

Cooling mode: 15 °C WB - 24 °C WB

 

Heating mode: 15 °C DB - 27 °C DB

*1   Cooling/Heating capacity indicates the maximum value at operation under the following condition.

 

Cooling:Indoor: 27 °C DB/19 °C  

WB Outdoor: 35 °C DB

 

Heating:Indoor: 20 °C DB  

Outdoor: 7 °C DB/6 °C WB

*2  The value in the parenthesis are for the PEAD-M•JAAD model.

*3  The external static pressure is set to 50 Pa at factory shipment.

*4  The operating noise is the data that was obtained in an anechoic room.

Summary of Contents for Mr. SLIM PEAD-M100JAA













Reviews: