Door adjustment
If the adjustment bolt is not in contact with the floor, lower the bolt, and adjust it so that the caster is slightly above the floor.
When the refrigerator is installed in the corner of the room, the bolt of the refrigerator may sink into the floor and cause the refrig-
erator to tilt. It is recommended to make adjustments by objects like boards beforehand.
When the refrigerator bolt sinks into the floor, and it can be confirmed visually, prevent sinking by using objects like boards.
<Adjusting refrigerator compartment doors>
• Common elements
First, check the installation condition.
Note: The refrigerator weighs about 100 kg, and is held by 4 bolts. How far each bolt sinks into the floor depends on
factors such as floor pillars. Change in balance due to position of stored food (such as large or small amount of food
stored in the door pockets) may also affect sinking.
Problem
Solution
Adjusting doors horizontally
B
A
A
B
A
B
Adjusting vertical space between doors
Too much space
Not enough space
A > B (More space in outer side)
Or
A < B (More space in inner side)
A > B (Too much space between the
ice making compartment and versa
compartment doors.)
Misaligned versa compartment door
Misaligned ice making compartment
doors
A < B (Small space between the ice
making compartment and versa com-
partment doors.)
Misaligned versa compartment door
Misaligned ice making compartment
door
Place spacer set under the
outer roller of the tilted door
(ice making compartment door
in the above illustration) to
adjust
position.
Place spacer set under the
inner roller of the tilted door
(ice making compartment door
in the above illustration) to
adjust
position.
Replace roller set of the right
and left versa compartment doors.
a To adjust about 0.5 mm replace
with roller set C.
b To make large adjustment replace
with roller set D.
Replace lower roller set of the ice
making compartment door.
c To adjust about 0.5 mm replace
with roller set A.
d To make large adjustment replace
with roller set B.
Replace roller set of the right
and left versa compartment doors.
a To adjust about 0.5 mm replace
with roller set A.
b To make large adjustment replace
with roller set B.
Replace lower roller set of the ice
making compartment door.
c To adjust about 0.5 mm replace
with roller set C.
d To make large adjustment replace
with roller set D.
<Adjusting ice making compartment and versa compartment doors>
Right 0.5 [09]
Right 1.0 [11]
Left 0.5
[13]
Left 1.0
[15]
Marking
LH
RH
Identifying roller sets (Marking)
Right 0.5 [10]
Right 1.0 [12]
Left 0.5
[14]
Left 1.0
[16]
Marking
LH
RH
Roller set A (0.5 mm to the right)
Roller set B (1.0 mm to the right)
Roller set C (0.5 mm to the right)
Roller set D (1.0 mm to the right)
09
11
13
15
10
12
14
16
Check points after adjustment
When adjustments such as hinge position have been made without food in the door pockets, confirm the door position again with food stored inside.
When the refrigerator is moved to make adjustments in the back bolts, floor may be damaged due to objects trapped in the caster. It is recom-
mended to take preventive measures such as cleaning around the refrigerator and covering the floor with boards before moving the refrigerator.
After adjusting the refrigerator compartment doors, confirm auto closer operation.
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Copyright 2010 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Dec. 2010 No. OAH110 7
Made in Japan
New publication, effective Dec. 2010
Specifications subject to change without notice
