93
CHAPTER 11 TROUBLESHOOTING
11
11.
6 Er
ror Code
List
(1) Error code list (1 to 10000)
The following lists the error messages, error conditions, causes, and actions of the error codes (1 to 10000).
The "
Supplementary information" in the "Error and cause" column can be confirmed by any of the following.
• PLC Diagnostics in GX Works2
• Common error information (SD5 to SD15)
• Individual error information (SD16 to SD26)
Error
code
Error and cause
Action
1000
[HEAD UNIT DOWN]
The head module is running away or faulty.
• Malfunction due to noise
• Hardware failure
■
Supplementary information
• Common information:
• Individual information:
■
Diagnostic timing
• Any time
Take action against noise, and reset the module.
If this error occurs again, the hardware of the head module may be faulty.
(Please consult your local Mitsubishi representative.)
1001
1002
1003
1004
1005
1006
1009
1035
1090
[HEAD UNIT DOWN]
The head module is running away or faulty.
• Malfunction due to noise
• Hardware failure
■
Supplementary information
• Common information:
• Individual information: Breakdown information
■
Diagnostic timing
• Any time
Take action against noise, and reset the module.
If this error occurs again, the hardware of the head module may be faulty.
(Please consult your local Mitsubishi representative.)
1101
[RAM ERROR]
The RAM built in the head module is faulty.
■
Supplementary information
• Common information:
• Individual information:
■
Diagnostic timing
• When powered on or reset
Take action against noise, and reset the module.
If this error occurs again, the hardware of the head module may be faulty.
(Please consult your local Mitsubishi representative.)
1102
1103
1104
1161
[RAM ERROR]
The data in the device memory built in the head module were
overwritten.
■
Supplementary information
• Common information:
• Individual information:
■
Diagnostic timing
• Any time
Take action against noise, and reset the module.
If this error occurs again, the hardware of the head module may be faulty.
(Please consult your local Mitsubishi representative.)
1310
[I/O INT. ERROR]
An interrupt occurred even though there is no module that can
issue an interrupt.
■
Supplementary information
• Common information:
• Individual information:
■
Diagnostic timing
• When an interrupt occurred
The hardware of any of the installed modules is faulty. Check the installed
modules, and replace the faulty module. (Please consult your local Mitsubishi
representative.)
1311
[I/O INT. ERROR]
An interrupt request from a module installed with the head
module was detected.
■
Supplementary information
• Common information:
• Individual information:
■
Diagnostic timing
• When an interrupt occurred
The hardware of any of the installed modules is faulty. Check the installed
modules, and replace the faulty module. (Please consult your local Mitsubishi
representative.)
Summary of Contents for MELSEC-L SSCNETIII/H
