manualshive.com logo in svg

Mitsubishi Electric MELSEC FX2N-64CL-M, User Manual

Share
Download
Mitsubishi Electric MELSEC FX2N-64CL-M User Manual Download Page 17

Specifications 2

2-1

2.

Specifications

This section explains the specifications of the FX

2N

-64CL-M.

DESIGN PRECAUTIONS

When a remote I/O unit fails, outputs may randomly set ON or OFF, therefore, build an
external monitoring circuit that will monitor any input signals that could cause a serious
accident.

DESIGN PRECAUTIONS

•

Do not bind control and flat cables dedicated to CC-Link/LT together with power cables. 
Keep control and flat cables dedicated to CC-Link/LT away from major circuits and power
cables by 100 mm (3.93") or more.
It may cause a malfunction due to noise interference.

•

Use the FX

2N

-64CL-M in such status that any force is not applied on connectors for CC-

Link/LT interface and flat cables dedicated to CC-Link/LT. 
If any force is applied, wire breakage and failure may be caused.

STARTING AND MAINTENANCE PRECAUTIONS

•

Do not touch the terminals while the power is ON. It may cause an electric shock or
malfunction.

•

Shut down all phases of the power supply outside the master block before starting any
cleaning procedures. 
If the power is not disconnected from all sources, the FX

2N

-64CL-M may fail or

malfunction.

STARTING AND MAINTENANCE PRECAUTIONS

•

Do not disassemble or modify the FX

2N

-64CL-M. 

Doing so may cause failure, malfunction, injury, or fire.

•

The case of the FX

2N

-64CL-M is made of resin. 

Do not drop or apply strong impacts to the FX

2N

-64CL-M.

DISPOSAL PRECAUTIONS

•

Treat the FX

2N

-64CL-M as industrial waste when disposing of the product.

FX2N-64CL-M CC-Link/LT Master Block

Summary of Contents for MELSEC FX2N-64CL-M











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands