![background image](http://html.mh-extra.com/html/mitsubishi-electric/m-series/m-series_manual_238287582.webp)
M series
C-580
MULTI SYSTEM Inverter Heat Pump
MUL
TI
SYSTEMS
INST
ALLA
TION
PROCEDURE
9. Electrical work
Cautions for electrical work.
Warning:
• Always use dedicated circuits with breakers, and at the rated voltage.
Power supply circuits with insufficient capacity, and bad workmanship dur-
ing installation, may result in electric shock or fire.
• Always ensure that electrical wiring inlets are sealed when the branch box is
installed outdoors.
Rainwater on the terminal blocks may result in fire or malfunction.
Caution:
• Be sure to establish an earth. Do not earth the unit to a utility pipe,
arrester, or telephone earth.
Incomplete earth may cause electrical shock. A high surge current from
lightning or other sources may cause damage to the air conditioner.
• Use the specified electrical wiring and ensure that it is connected properly,
and that it is not under tension.
Failure to follow these requirements may result in broken wiring, heating, or
fire.
Wiring connecting branch box and outdoor unit, and branch box and indoor
units, functions as both power supply and signal cable. Connect this wiring
in accordance with the terminal block numbers to ensure correct polarity.
Ensure that the appropriate refrigerant piping and electrical wiring are con-
nected to each indoor unit. Incorrect wiring will interfere with the correct
operation of the unit.
Connect refrigerant pipes and connection wires to the appropriate ports
marked with matching alphabets (Ex. A, B, C, D, E) on this unit.
►
Always fix each ground wire separately with a ground screw.
To prevent that wiring installed in the ceiling is chewed by rats etc., it should
be installed in wiring conduit.
1. Remove the screws in the cover. (Fig. 9-1)
2. Remove the cover.
3. Pass the wiring into the branch box. (Fig. 9-2)
4. Fix each wire in place with a wiring clamp. (Fig. 9-3)
5. Firmly connect each wire to the appropriate terminal block. (Fig. 9-3)
6. Replace the cover.
7. When the branch box is installed outdoors, ensure that the wiring inlets are
sealed with putty to prevent entry of rainwater. (Fig. 9-2)
Electric cover
3-Bush
Seal
Wiring
BC controller
Band
Terminal block: TB2B <To outdoor unit> ø1.6 - ø2.0
Terminal block: TB3A-TB3E <To indoor unit> ø1.6
9.1. When using wiring conduit (Fig. 9-4)
Replace the horizontal cover when the wiring conduit has been fixed in place.
Cover
Wiring conduit
Washer
Nut
Wiring conduit
Wiring conduit of up to 1" OD may be used.
(1) When using 1" OD wiring conduit, remove the bush and fix to the branch box.
Remove the horizontal cover while fixing to the branch box.
(2) When using wiring conduit of 3/4" OD or smaller, notch the bush and insert the
wiring conduit approximately 100 mm into the branch box.
* Replace the horizontal cover when the wiring conduit has been fixed in place.
Fig. 9-1
Fig. 9-2
Fig. 9-3
S1
S2
S3
S1
S2
S3
S1
S2
S3
S1
S2
S3
S1
S2
S3
S1
S3
S2
TB3C
TB3
E
TB3A
TB3B
TB3D
TB2B
Fig. 9-4
*
Summary of Contents for M-SERIES
