Mitsubishi Electric Climaveneta i-BX 010-035T, Installation, Operation And Service Manual

Page: 71 / 80

SYSTEM CONFIGURATION
U I A
Description Menu
Parameter
no.
Default Write set value UOM
Select system configuration
Enable zone management
NOT = Disabled
YES = Enabled
Mn01 016A NOT YES -
System type (table 1) Mn01 0101 0 3* -
Mixing valve ZONE 1
Type of mixing valve 1= 0-10V Mn01 012T 0-10
HEATING compensation curve ZONE 1
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0167 NOT
Heating compensation curve number Mn01 0174 0,7
Enable room temperature influence
NOT = Disabled YES = Enabled
Mn01 0178 NOT
Room Authority Mn01 0179 30 %
MINIMUM set point limit for curve Mn01 0180 23 °C
MAXIMUM set point limit for curve Mn01 0181 45 °C
COOLING compensation curve of ZONE 1
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0169 NOT
Maximum temperature set point limit in cooling mode (Tm1) Mn01 0132 20 °C
Minimum outside temperature corresponding to max. outlet
temperature (Te1)
Mn01 0133 23 °C
Minimum temperature set point limit in cooling mode (Tm2) Mn01 0134 18 °C
Maximum outside temperature corresponding to min. outlet
temperature (Te2)
Mn01 0135 36 °C
HUMIDITY CONTROL ZONE 1
Enable compensation for room humidity, ZONE LT1
NOT = Disabled YES = Enabled
Mn01 0171 NOT
Room relative humidity value to start increasing water temperature
set point
Mn01 0172 70 %
Maximum outlet temperature hysteresis corresponding to 100%
relative humidity
Mn01 0173 15 °C
Enable contact kA11 as DEHUMIDIFIER (The contact closes and the
dehumidifier is activated when the humidity measured by the probe on
the A5 room controller exceeds the value set for parameter 0172)
Mn01 011B DEHUMIDIFIER
HEATING compensation curve ZONE 2
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0152 NOT -
Compensation curve number Mn01 0159 1 -
Enable room temperature influence
NOT = Disabled
YES = Enabled
Mn01 0163 NOT -
Room Authority Mn01 0164 30 %
MINIMUM set point limit curve Mn01 0165 30 °C
MAXIMUM set point limit curve Mn01 0166 48 °C
COOLING compensation curve ZONE 2
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0154 NOT -
Maximum temperature set point limit in cooling mode (Tm1) Mn01 0128 20 °C
Minimum outside temperature corresponding to max.
temperature (Te1)
Mn01 0129 23 °C
Minimum temperature set point limit in cooling mode (Tm2) Mn01 0130 18 °C
Maximum outside temperature corresponding to min.
temperature (Te2)
Mn01 0131 36 °C
ZONE 2 room controller address setting addr 1 11*
Device address setting
Low temperature ZONE LT1 room control unit address setting addr 1 14
High temperature ZONE HT1 room control unit address setting addr 1 11
System number 3
Parameter configuration
The SYSTEM compensation curve in HEATING mode, parameter 0159, must be set so as to reach an outlet temperature suitable for the high
temperature zone with radiators. The mixed zone is managed according to the compensation curve set for parameter 0174.
The room unit (A5), supplied as standard with the heat pump, controls the room temperature in zone 1, with radiant panels, the additional room
unit (accessory) controls the room temperature in zone 2, with radiators or fan coils.
Enable contact HL1 as secondary circuit pump:
- RELAY ALARM
- DEHUMIDIFIER
- AT1 PUMP
- SUMMER/WINTER
Mn01 015A
RELAY
ALARM
AT1 PUMP
EN i-BX-(Y)_i-BX-N-(Y) 71
* obligatory values for the present configuration