Mitsubishi Electric CITY MULTI P500YMF-C Service Handbook Download Page 94

Page: 94 / 148

–92–

2) Temperature Sensor

Thermistor troubleshooting flow

Start

Disconnect applicable thermistor
connector from the board.

Measure temperature of applicable
thermistor (actual measured value).

Check thermistor resistance value.

Compare temperature for thermistor
resistance value with actual mea-
sured valued.

difference?

Insert applicable thermistor connector
into board, and check sensor input
temperature on LED monitor for differ-
ence.

difference?

No abnormality.

Change thermistor.

Check for connection
problem.

Change the controller
board.

Note 5

Yes

Note 4

Note 2

Note 1

Note 3

Summary of Contents for CITY MULTI P500YMF-C





















































































































































Search results

Summary of Contents for CITY MULTI P500YMF-C

Reviews:

Related manuals for CITY MULTI P500YMF-C

Brands by name

Popular brands

Mitsubishi Electric CITY MULTI P500YMF-C, Service Handbook

Search results

Summary of Contents for CITY MULTI P500YMF-C

Reviews:

Related manuals for CITY MULTI P500YMF-C

Brands by name

Popular brands