Mitsubishi Daiya SRK20HB, User Manual

Page: 13 / 20

– 12 –
Remote control handling procedure
Replacing the batteries
The following cases signify exhausted batteries. Replace old batteries with new ones.
•
Receiving beep is not emitted when a signal is transmitted.
• Indicator fades away.
•
On the battery is printed its expected life. This may
be shorter than that of the air conditioner,
depending on the date of manufacture.
• However, the battery may still be in working order
after expiry of its nominal life.
About TIMER operation
About FAN (circulator) mode operation
• When the room is being heated by a stove or otherwise, use the circulator for more efficiency.
If the room is warmer than the set temperature, the unit switches to FAN, and stops again when the set temperature is reached. FAN starts again
when the room reaches the set temperature plus 2°C.
• FAN operation continues if set to continuous.
Check the room
temp. 60 mins. in
advance.
▼
▼
Set temperature
Set time
1
In COOL operation
(Stop) Operation starts
(Operation)
About FAN SPEED
■
You can choose the capacity of your air conditioner when heating or cooling.
About Amenity facilities
Amenity facilities enable to start the operation a little earlier, so that the
room approaches optimum temperature at ON time when the operation is
started by ON-TIMER.
•
Mechanism
The room temperature is checked 60
minutes before the timer is at ON.
Depending on the temperature at that
time, the operation starts 5 to 60
minutes before the timer is at ON.
• The Amenity facility only functions
for COOL and HEAT operation mode
(including AUTO). It does not work
for DRY and FAN mode.
NOTE
• Don't use old and new batteries together.
• Remove the batteries when the remote control is not
used for a long period.
• The life of a battery conforming to JIS or IEC is 6 to
12 months with normal use. If used longer, or when an
unspecified battery is used, liquid may leak from the
battery, causing the remote control to malfunction.
Using the remote control holder
The remote control can be
attached to a wall or pillar by
using a remote control holder.
Before installing the remote
control, check that the air
c o n d i t i o n e r r e c e i v e s t h e
signals properly.
For installing or removing the
remote control, move it up or
down in the holder.
Operation capacity by your choice FAN SPEED
Set automatically by microcomputer AUTO
Powerful operation with high capacity HI
Standard operation MED
Energy-saving operation LO
Remove back lid and take out old batteries
2
Insert new batteries (SUM-4 or R03x2)
3
Close back lid
About OFF-TIMER Operation
When OFF-TIMER operation is selected, the room temperature is
automatically controlled after a while, ensuring that the room is not too
cold during cooling or too warm during heating.
•
During COOL and DRY: the pre-set temperature is raised by 0.5°C at the
start of OFF-TIMER operation (when the timer is set). After that, the
temperature goes up by 0.5°C every 30 minutes to become 1.5°C higher
within one hour.
• During heating: Preset temperature is lowered by 1°C at the start of OFF-
TIMER operation (when the timer is set). After that the temperature is
lowered by 1°C every 30 minutes to become 3°C lower in an hour and
10°C lower in two hours.
• After the OFF-TIMER operation has been conducted for 2 hours, the
operation may be stopped earlier than the set time depending on the
temperature condition at that time.
• After the OFF-TIMER operation has been conducted for 2 hours, the unit
is operated with the LOW air flow.
■
When the indicator shows any abnormal condition,
Press the reset switch with the tip of a ballpoint pen.
Attention to the
+ and – marks
P.1-18/E 04.10.19, 10:27 AM 12