Mircom FR-320 Series Installation And Operation Manual Download Page 94

Page: 94 / 112

Pre-Programmed Modes

12.14 Mode 14: Pre-action/deluge, Single Hazard, Not Cross Zoned,

Combined Release

12.14.1 Zone Configuration

•

Detection Zone -1: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -2: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -3: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -4: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -5: Supervisory

•

Detection Zone -6: Water-flow.

•

NAC -1: Signal, steady on any alarm.

•

NAC -2: Escalating Signal, indicates Hazard Area 1 status, Supervisory Optional.

•

RAC -1: Releasing Circuit (Hazard Area 1)

•

RAC -2: Releasing Circuit (Hazard Area 1)

12.14.2 Hazard Configuration

•

Default Release Timer Value: 0 seconds

•

Default Manual Release Delay: 0 seconds (not used)

•

Default Abort Delay Type: Standard UL (not used)

•

Default Soak Timer Value: 0 seconds (continuous)

12.14.3 NAC Configuration

•

Default Escalating NAC code of Hazard Area State:

•

Hazard Idle: Off

•

Hazard Alert: Temporal (see Table 7)

•

Hazard Alarm: Temporal (see Table 7)

•

Hazard Release: Steady

•

Default NAC code of Supervisory is 20 BPM.

Attention: This mode of operation is neither FM nor UL approved.

Detection Zones

Phantom Zones

Zp1

RT1

Exp

Alm

Supv

Z1+Z2+Z3

Out1

Signal

Steady

Out2

Signal

Escalating

(X)

Out3

Rel.

Releasing

Out4

Rel.

Releasing

RLS TMR 1 Started

RLS Tmr 1 Interrupted

RLS Tmr 1 Cancelled

Summary of Contents for FR-320 Series

















































































































Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands

Mircom FR-320 Series, Installation And Operation Manual

Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands