Mircom FR-320 Series Installation And Operation Manual Download Page 88

Page: 88 / 112

Pre-Programmed Modes

12.11 Mode 11: Agent Release, Single Hazard, Cross-zoned,

Combined Release

12.11.1 Zone Configuration

•

Detection Zone -1: Alarm (Hazard Area1, cross-zoned)

•

Detection Zone -2: Alarm (Hazard Area1, cross-zoned)

•

Detection Zone -3: Alarm (Pressure Switch or Water-flow)

•

Detection Zone -4: Supervisory (Default non-latching)

•

Detection Zone -5: Abort Switch

•

Detection Zone -6: Manual Release

•

NAC -1: Signal, indicate the Hazard Area1 status.

•

NAC -2: Signal, indicate the Hazard Area1 status.

•

RAC -1: Releasing Circuit

•

RAC -2: Releasing Circuit

12.11.2 Hazard Configuration

•

Default Release Timer Value: 60 seconds

•

Default Manual Release Delay: 0 seconds

•

Default Abort Delay Type: Standard UL.

•

Soak Timer Value: 0 seconds (continuous)

12.11.3 NAC Configuration

•

Default Escalating NAC code of Hazard Area State:

•

Hazard Idle: Off

•

Hazard Alert: Steady

•

Hazard Alarm: 60BPM

•

Hazard Release: Steady

•

Default NAC code of supervisory is 20 BPM

Detection Zones

Phantom Zones

Release Timers

Zp1

Zp2

RT1

Exp

RT2
Exp

Alm

Supv

Z1+Z2

Z3+Z4

Out1

Signal

Steady

Out2

Signal

Escalating

(X)

Out3

Rel.

Releasing

Out4

Rel.

Releasing

RLS TMR 1 Started

RLS Tmr 1 Interrupted

RLS Tmr 1 Cancelled

RLS Tmr 2 Started

RLS Tmr 2 Interrupted

RLS Tmr 2 Cancelled

Summary of Contents for FR-320 Series

















































































































Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands

Mircom FR-320 Series, Installation And Operation Manual

Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands