background image

- 2 -

• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.

• Fits rear wheel hub width between 125 and 140mm. 

Hub nut type rear wheel axles are not compatible without using the replacing the left side coupling bolt (UF-8S) 

with the optional Left Side Coupling for Hub Nut Axle (UF-8L).

• Fits tire which outer diameter is between 570 and 710mm (Gravity Mode) or 610 and 710mm (Fixed Mode). 

Any other sizes cannot be used on LR961.
A slick tire MUST be used with all tire drive trainer like the LR961. Use of a non slick or knobby tire will cause 
severe damage to both the trainer and your tire and will void any warranty.

• Packed in completely assembled condition. However, you will need tools for adjusting the center foot length 

or the remote shifter band. The tools don't come in the kit, you need to prepare separetely.

• Use the supplied rear quick release skewer for maximum stability. The hub clamping parts (couplings) fits the 

supplied quick release skewer only. Minoura is not responsible for any problem caused from using your own 

skewer.

• Be careful not to pinch your finger when raising up or folding down the Mag unit, or folding the frame.

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire and roller contact will eventually wear both your tire and the trainer roller.

Wipe the tire surface to remove any solid dust away before setting the bike on the trainer in order to maximize 

both the tire and the drive roller life. And maintain the tire air pressure 10% higher.

• Touching the spinning wheel and/or any other moving parts while training may cause serious injury.

  Keep children and pets away from the trainer when in use.

• It is not possible to convert the remote controllable resistance unit to the non-remote version one.

  Removing the remote shifting device means fixing the resistance level at the highest range.

• To protect the floor or carpet from stain and sweat during workout, we recommend you to put a sheet or mat 

under the trainer and bike.

• If you feel any strange noise or smell, stop using LR961 immediately and contact the retailer where you 

purchased the trainer. Do not try to disassemble LR961 without our prior approval.

• Any warranty will be void if you use LR961 for other purpose than instructed.

Minorua offers 

1-year limited warranty

 on this product from the date of your purchase for any problem 

caused by manufacturer's defect.

Any damage or problem caused by transporting process or user's misuse, also the natural wear will not be 

covered under warranty.

Any damage from shipping or moving must be made to the shipping company.

Read the enclosed "

Minoura Limited Warranty Policy

" card for more detail.

For the latest information, refer Minoura web site (http://www.minoura.jp/english/).

Important Notes

Please read carefully before use

Summary of Contents for LiveRide LR961









Reviews: