MINN KOTA 1865120, Manual

Page: 7 / 14

11
12
ITEM(S) NEEDED
#8 x 1
ad. Once the Splicers are secure on both wires, take the
Shrink Tubes and slide them over the Splicers. The
Shrink Tubes should be centered over the Splicers and
completely cover the wire connections.
Minn Kota Consumer & Technical Service
Johnson Outdoors Marine Electronics, Inc.
PO Box 8129
Mankato, MN 56001 121 Power Drive
Mankato, MN 56001
Phone (800) 227-6433
Fax (800) 527-4464
minnkotamotors.com
©2022 Johnson Outdoors Marine Electronics, Inc.
All rights reserved.
Part #2377182 Rev A 05/22 ECN 42520
For warranty information, please visit minnkotamotors.com .
11ad
11ae
Plug Assembly Plug Assembly
Plug Assembly Plug Assembly
Splice Cover Splice Cover
Shrink Tube Shrink Tube
Positive Power Positive Power
Lead (+) Lead (+)
Negative Power Negative Power
Lead (-) Lead (-)
Negative (-) Negative (-)
Power Lead Power Lead
Splicer Splicer
Splicer Splicer
Splicer Splicer
Shrink Tube Shrink Tube
Shrink Shrink
Tube Tube
Shrink Shrink
Tube Tube
11ac
#6 x 1
ab. The other Splicer and Shrink Tube should be added to
the Plug Receptacle so it can be attached to the Boat
Wires. Take the Plug Receptacle (Item #B) and place
one Shrink Tube (Item #6), followed by one Splicer
(Item #8) on the end of the black Negative (-) Wire of
the Plug Receptacle. Secure the Splicer by tightening
the Set Screw with a 3/32" Allen Wrench (Item #14) to
20 in-lbs.
ac. Take the Plug Assembly and identify the red Positive
(+) Power Lead on the Plug Assembly and align
it with the Positive (+) Power Lead on the Trolling
Motor Wires. Insert it into the Splicer at the end of
the Positive (+) Lead Wire from the Plug Assembly.
Take the black Negative (-) Power Lead from the Plug
Assembly and align it with the Negative (-) Power Lead
from the Trolling Motor Wires. Insert it in the Splicer at
the end of the black Negative (-) Power Lead of from
the Trolling Motor Wires. Secure the Set Screw of both
Splicers with the 3/32” Allen Wrench.
NOTICE:
The Shrink Tubes are meant to water
proof the connection between the Plug Assembly
and the Trolling Motor Wires. Make sure there are
no gaps around the wires that would allow water to
reach the connection.
NOTICE:
When disconnecting the Plug Assembly
from the Receptacle, be sure to install and tighten the
Dust Cap. This will prevent water or debris intrusion.
Plug Plug
Assembly Assembly
Plug Plug
Assembly Assembly
11ab
Positive (+) Positive (+)
Power Lead Power Lead
Positive (+) Positive (+)
Power Lead Power Lead
Negative (-) Negative (-)
Power Lead Power Lead
Trolling Trolling
Motor Wires Motor Wires
ae. When satisfied with the position, secure the Shrink
Tubes in place with a Heat Gun. Then slide the Splice
Cover over the Shrink Tubes to complete
the installation.
NOTICE:
When connecting the Plug Assembly to the
Receptacle, be sure to tighten the Threaded Collar
to ensure a proper water-tight seal. A water-tight seal
protects electrical contacts. Failure to tighten the
Threaded Collar could result in water intrusion.
Threaded Threaded
Collar Collar
#14 x 1