manualshive.com logo in svg

Minebea OPT-563B, Quick Instruction Manual

Share
Download
Minebea OPT-563B Quick Instruction Manual Download Page 9

 

7 

1-2. Rear Panel 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

(1) Power supply terminal board 

Connected to the AC power supply and grounding wire. 

 

(2) Protective ground terminal 

Connect this to ground to eliminate noise effects such as static electricity. Do not connect any wires 
other than the grounding wire. 
This connector is internally linked to F.G. on the power supply terminal board. 

 

(3) External control input/output connector 

Used to connect the external control device. 

 

(4) Torque transducer/rotation speed detector connector 

Connect the signal cable to the torque transducer/rotation speed detector (MP-9820). 

 

(5) Analog output connector 

Connect the signal cable to the analog input device. 

 

(6) Optional part mounting section 

One optional part (RS-232C, RS-422/485, PROFIBUS, or CANopen) can be mounted. 

(1) Power supply   
   terminal board 

(2) Protective   
   ground terminal 

(6) Optional part   
   mounting section

(3) External control   
   input/output connector 

(4) Torque transducer/rotation speed   
   detector connector 

(5) Analog output connector 

Summary of Contents for OPT-563B































Reviews:

No comments

Brands by name

Popular brands

Load more brands