manualshive.com logo in svg

Minebea Intec Puro EF-4PLLP-1500, Operating Instructions Manual

Share
Download
Minebea Intec Puro EF-4PLLP-1500 Operating Instructions Manual Download Page 9

Symbol

Charge level

0 to 10 % Remaining
11 to 40 % Remaining
41 to 70 % Remaining
71 to 100 % Remaining

Note:

When battery symbol blinks fast, approximately 30 minutes working time is left.

When [lo.bat] is displayed, the scale will shut off.

Charging the scale must be performed in a dry environment.

WARNING

Risk of explosion can occur

If the rechargeable battery is replaced with the wrong type or if it is not properly
connected.

Battery is to be replaced only by an authorized Puro® service dealer.

Dispose of battery according to local laws and regulations.

3.4

Connections

1

2

3

4

Pos.

Description

1

Accessory

2

DC IN USB-C

3

Printer port

4

LC (load cell)

3.4.1

Connect printer

A printer can be connected to the printer port on the side of the indicator.

3.5

Mounting bracket

Align the mounting bracket over the threaded holes in the side of the indicator and install
the knobs. Adjust the indicator to the desired angle and tighten the knobs.

3 Device installation

Floor scale Puro®

Minebea Intec

EN-7

Summary of Contents for Puro EF-4PLLP-1500
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands