Minebea Intec CAS1 Operating Instructions Manual Download Page 88

Page: 88 / 160

— B.LEUCHT

8.8 - Illumination of the display

— EIN

8.8.1 - On*

— AUS

8.8.2 - Of

— AUTO.AUS

8.8.3 - Automatic switch of according to timer

(see Chapter

6.3.6.1

menu item [TIMER] 8.9)

The keyboard can be locked and unlocked for input in the setup menu at [TASTEN] 8.3.

7.1.5.4

Combics automatic Switch of

Menu: [SETUP]- [BETRIEB]- [PARAMET]- [AUTO.AUS] (8.7) (see also Chapter

6.3.6.1

)

Under [AUTO.AUS] 8.7 in the setup menu, it is possible to set that the is switched of

automatically after a time speciied using the timer.

7.1.5.5

Illumination of the display

Menu: [SETUP]- [BETRIEB]- [PARAMET]- [B.LEUCHT] (8.8) (see also Chapter

6.3.6.1

)

The following settings for the illumination of the display can be made in the setup menu

under [B.LEUCHT] 8.8:

* Factory setting

7.1.5.6

Timer

Menu: [SETUP]- [BETRIEB]- [PARAMET]- [TIMER] (8.9) (see also Chapter

6.3.6.1

)

The timer for switching of the device and/or display illumination can be set to 2, 4 or

10 minutes in the setup menu under [TIMER] (8.9).

7.1.5.7

Example: Setting device parameters

Example: Switch on, zero, tare container weight, ill container, switch to display gross

weight, second weight unit or 10x resolution.

All segments of the display appear (display test).

1. Switch on the device with key

The display for the unloaded scale appears.

2. Press the

key to zero the scale.

The zeroed scale display appears.

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

7 Operating

EN-86

Minebea Intec

Summary of Contents for CAS1

































































































































































Search results

Summary of Contents for CAS1

Reviews:

Minebea Intec CAS1, Operating Instructions Manual, Page: 88 / 160

Search results

Summary of Contents for CAS1

Reviews: