The message [
The message [
Calibration Completed!
Calibration Completed!
] is displayed
] is displayed after a successful calibration. Otherwise,
after a successful calibration. Otherwise,
a corresponding message will be
a corresponding message will be displayed.
displayed.
5.4.7 C.O. Test
5.4.7 C.O. Test
Tools required:
Tools required:
Medsim300B Patient simulator, MPS450, or
Medsim300B Patient simulator, MPS450, or equivalent equipment
equivalent equipment
C.O. adapter box (for 300B, use CI-3, P/N 3010-0289; for MPS450, use
C.O. adapter box (for 300B, use CI-3, P/N 3010-0289; for MPS450, use P/N 5180500)
P/N 5180500)
C.O. main cable (P/N:
C.O. main cable (P/N: 0010-21-42716)
0010-21-42716)
1.
1.
Connect
Connect the patie
the patient sim
nt simulator to
ulator to the C.O.
the C.O. connector
connector using
using the C.O.
the C.O. main c
main cable thr
able through
ough
the adapter box.
the adapter box.
2.
2.
Set t
Set the blood
he blood temperature
temperature (BT) t
(BT) to 37ºC
o 37ºC on the
on the patient
patient simulator
simulator and che
and check the
ck the
temperature value is 37±0.1ºC.
temperature value is 37±0.1ºC.
3.
3.
In
In the
the [[
C.O. Setup
C.O. Setup
] menu, set [
] menu, set [
Auto IT
Auto IT
] to [
] to [
Off
Off
], set [
], set [
Manual TI(°C)
Manual TI(°C)
] to [
] to [
2°C
2°C
], and set
], and set
[[
Comp. Const
Comp. Const
] to [
] to [
0.542
0.542
]. Select [
]. Select [
Enter C.O. Screen
Enter C.O. Screen
] to open the C
] to open the C.O. Screen.
.O. Screen.
4.
4.
Click
Click [[
Start
Start
] to start C.O. measurement.
] to start C.O. measurement.
5.
5.
On the
On the C.O. simul
C.O. simulator, se
ator, set the
t the C.O. to
C.O. to 5 L
5 L/min. Wait
/min. Wait for
for 3 to
3 to 10 seco
10 seconds.
nds.
6.
6.
Verify
Verify that
that the
the C.O.
C.O. value
value is
is 5±0.25
5±0.25 L/min.
L/min.
5.4.8 CO
5.4.8 CO
2
2
(M02D) Test and Calibration
(M02D) Test and Calibration
Leakage Test
Leakage Test
1.
1.
Connect
Connect CO
CO
2
2
measurement assembly.
measurement assembly.
2.
2.
Wait
Wait for
for 10
10 minutes
minutes until
until the
the CO
CO
2
2
module warm-up is finished. Use your finger or other
module warm-up is finished. Use your finger or other
object to occlude the port. The CO
object to occlude the port. The CO
2
2
module will behave as follows:
module will behave as follows:
The alarm message [
The alarm message [
CO
CO
2
2
Filter Line
Filter Line Occluded
Occluded
] is displayed on the screen after 3
] is displayed on the screen after 3 seconds.
seconds.
Block the gas inlet for another 60
Block the gas inlet for another 60 seconds. Select [
seconds. Select [
User Maintenance >>
User Maintenance >>
] → enter the
] → enter the
required password → [
required password → [
Module Maintenance >>
Module Maintenance >>
] → [
] → [
Maintain CO
Maintain CO
2
2
>>
>>
] → [
] → [
Calibrate
Calibrate
CO
CO
2
2
>>
>>
]. If the flow rate is less
]. If the flow rate is less than 10 ml/min and the
than 10 ml/min and the alarm message continues, it indicates
alarm message continues, it indicates
that the module does not
that the module does not leak.
leak.
Accuracy Test
Accuracy Test
Tools required:
Tools required:
A steel gas cylinder with 6±0.05% CO
A steel gas cylinder with 6±0.05% CO
2
2
and balance gas N
and balance gas N
2
2
Summary of Contents for uMEC10
