background image

MIMAKI ENGINEERING CO., LTD.

URL: http://mimaki.com/

D203034-10

ソフトメディア搬送キット

Soft Media Feeding Kit

OPT-J0400

Table of Contents

For English

For Japanese

Foreword ............................................... 2

DISCLAIMER OF WARRANTY...............2
On This Operation manual ......................2
Requests .................................................2

About installing this machine ................. 3

Where to Install This Machine .................3

Names of Parts and Functions .............. 4

Front Side of the Machine .......................4
Rear Side and Right Side of 
the Machine.............................................4

Media..................................................... 5

Usable sizes of media .............................5
Caution in handling of medias .................5

Setting a Media...................................... 6

Adjusting the Head Height.......................6
Setting a roll media..................................6
Please check the work after setting the 
media.......................................................8
When using small take-up device............9

Maintenance ........................................ 11

Precautions for Maintenance.................11
About Cleaning Solution........................11
Cleaning the tension roller.....................11

Troubleshooting................................... 12

Media get jammed / media is soiled ......12
Image quality is poor .............................12
When media heaves up at feeding........13
If the wrinkles on the platen...................13
If the ink landing position is shifted in
 the Y direction ......................................13
When using non-recommended 
medias...................................................13

はじめに

.............................................. 15

ご注意

................................................... 15

取扱説明書について

............................. 15

おねがい

............................................... 15

本機の設置について

............................ 16

設置場所について

................................. 16

各部の名称とはたらきについて

.......... 17

装置前面

............................................... 17

装置背面

/

側面

..................................... 17

メディアについて

............................... 18

使用可能メディアサイズ

...................... 18

メディア取り扱い上の注意

.................. 18

メディアをセットする

........................ 19

ヘッド高さを調整する

......................... 19

ロールメディアをセットする

............... 19

メディアをセットした後確認作業を
行ってください

.................................... 21

小巻取装置をお使いになる場合

........... 22

日常のお手入れ

................................... 24

お手入れ上のご注意

............................. 24

メンテナンス洗浄液について

............... 24

引張りローラーのお手入れ

.................. 24

故障?と思う前に

............................... 25

メディア詰まり

メディアが汚れる

..... 25

画質不良が発生したときは

.................. 25

メディアが搬送時に波打つ場合

........... 26

プラテン上にシワが発生する場合

....... 26

インクの着弾位置が

Y

方向に

ずれる場合

........................................... 26

弊社が推奨していないメディアを使用す
る場合

................................................... 26

Summary of Contents for OPT-J0400














Reviews: