Milwaukee MW806 MAX Instruction Manual Download Page 26

Page: 26 / 52

MW806

Portable Meter

Calibrating with Custom Buffers

Custom buffer value needs to be configured in pH mode Setup.

Temperature compensation of custom buffers is set to the value

of 25 °C.

Press RANGE/



. The custom buffer value is displayed blinking

on the third LCD line.

Use the



keys to modify the value based on temperature

reading. The buffer value is updated after 5 seconds.

ºC

ATC

CB1

10.01

9.18

7.01

CAL

25.0

1.7 5 P H

1.49

W A I T

ACCEPT

ºC

ATC

CB1

10.01

9.18

7.01

CAL

25.0

1.7 5 P H

1.71

Note: When using custom buffers, CB1 and CB2 tags are

displayed. If only one custom buffer is used, CB1 is displayed

together with its value.

Clear Calibration

1. Press CAL/EDIT to enter Calibration mode.

2. Press LOG/CLEAR.

ACCEPT tag is displayed blinking and “CLEAR CAL“ message

is displayed on the third LCD line.

3. Press GLP/ACCEPT to confirm.

“PLEASE WAIT“ message is displayed, followed by the

“NO CAL” confirmation screen.

ACCEPT

ºC

ATC

7.01

CAL

28.0

C A L

7.02

C L E A R

ºC

ATC

CAL

MEASURE

28.0

7.02

N O C A L

Summary of Contents for MW806 MAX





















































Search results

Summary of Contents for MW806 MAX

Reviews:

Related manuals for MW806 MAX

Brands by name

Popular brands

Milwaukee MW806 MAX, Instruction Manual

Search results

Summary of Contents for MW806 MAX

Reviews:

Related manuals for MW806 MAX

Brands by name

Popular brands