Milwaukee M18 FDEX, Operator'S Manual

Page: 4 / 8

4
SYMBOLOGY
Volts
Direct Current
Read Operator's Manual
SPECIFICATIONS
Cat. No. ................................................. M18 FDEX
Cat. No. ............................................... M18 FPDEX
Do not dispose of electric tools
together with household waste
material. Electric tools and electronic
equipment that have reached the end
of their life must be collected
separately and returned to an
environmentally compatible recycling
facility.
Regulatory Compliance Mark (RCM).
This product meets applicable
regulatory requirements.
Wear safety glasses.
For use only with M18 FH M18 FUEL™ 26 mm
SDS PLUS Rotary Hammer
For use only with M18 FHP M18 FUEL™
28 mm SDS PLUS Rotary Hammer
Min Bit Diameter ............................................ 5 mm
Recommended Ambient
Large Nozzle Max Bit Diameter................ 31.7 mm
Operating Temperature ................... -17°C to 51°C
Max depth ..................................................152 mm
Dust Box Cat. No .................................. 49902344
ASSEMBLY
3.
1. Turn OFF the tool.
2. Remove the battery pack.
4.
5.
Squeeze the dust box latches.
Pull the dust box away from the HAMMERVAC™.
Removing/Installing the Dust Box
and HEPA Filter
To remove the dust box:
Dust box
port
HEPA
6.
Empty debris by holding away
from the user’s face and tap-
ping dust box into a trash can,
pail, or other suitable
container. For best cleaning
results, connect a vacuum
hose with dust extraction
adaptor (Cat. No. 49901959)
to the dust box port and suc-
tion out debris.
If necessary, pull the HEPA filter away from the
dust box and tap clean. Do not clean with water
or compressed air. After about 1500 holes or loss
of suction, discard and replace HEPA filter (Cat.
No. 49902306).
To install the dust box:
1. Slide the dust box into the body of the
HAMMERVAC™.
2. The dust box latches should snap into place.
NOTE : Do not operate the HAMMERVAC™ without
Installing/Removing Nozzle
Replace the nozzle:
• After drilling about 1500 holes,
• When the bit brush shows signs
of wear,
• When suction is reduced,
• When dust escapes through the
bit brush during use
To r e p l a c e t h e S t a n d a r d
(Cat. No. 14520105 and Large
Cat. No. 14520110) nozzles,
rotate the nozzle release lever
down to the open position and
pull out nozzle from the lower nozzle assembly.
Slide the new nozzle into the lower nozzle assembly
and rotate the nozzle release lever up to the closed
position.
Dove tail slot
Front depth
bracket
Bit depth
gauge button
Tabs
Rear depth
bracket
screws
Rear depth
bracket
Removing/Installing the Depth Stop
To remove the depth stop:
depth bracket with a philips screwdriver.
4.
1. Turn OFF the tool.
2. Remove the battery pack.
3. Remove screws from left and right side of rear
Remove front
NOTE: Use a
depth bracket by pulling up on it.
snap, if needed.
To install the depth stop:
1. Place the rear depth bracket into the slot on the
top of the dedicated dust extractor.
2. Insert screws into the left and right side of rear
depth bracket with a philips screwdriver.
3. Insert front depth bracket into dove tail slot on
nozzle base and push down until snapped into
place.
V
WARNING
Only use accessories specifically
recommended for this tool.
Others may be hazardous. To reduce the risk of
injury, always remove the battery pack before
removing the dust box. Do not use tool without
dust box and HEPA filter in place.
CAUTION
Keep filter clean. Efficiency of the
HAMMERVAC™ is largely
dependent on the filter. A dirty filter will reduce
the air flow and overall efficiency of the system.
Do not clean with water or compressed air.
Remove from dust box and tap clean.
Nozzle Max Bit Diameter ............................. 16 mm