20
21
M18
ONEFSZ
.........................477908 02
...000001-999999
.....................300 mm
.......................20 mm
.......................25 mm
.......................25 mm
.....................150 mm
................0-3000 min
-1
.......................32 mm
.......................18 V
......................4.2
.......2400 – 2480 MHz
.........................0 dBm
............3,5 ... 4,6 kg
.................-18...+50 °C
................M18B2... M18HB12
.............. M12-18 ... ; M1418C6
........................85,4 dB (A)
........................96,4 dB (A)
........................26,7 m/s
2
..........................1,5 m/s
2
........................25,1 m/s
2
..........................1,5 m/s
2
ENGLISH
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING!
Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the
machine is running.
When working in walls ceiling, or
fl
oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must
fi
rst be drilled with a hole
corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. Milwaukee Distributors o
ff
er to
retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
No metal parts must be allowed to enter the battery section
of the charger (short circuit risk).
Use only System 18 V chargers for charging System 18 V
battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it o
ff
immediately with soap and
water. In case of eye contact rinse thoroughly for at least
10 minutes and immediately seek medical attention.
Warning!
To reduce the risk of
fi
re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in
fl
uid or allow a
fl
uid to
fl
ow
inside them. Corrosive or conductive
fl
uids, such as
seawater, certain industrial chemicals, and bleach or
bleach containing products, etc., can cause a short circuit.
WARNING
This device contains a lithium button/coin
cell battery. A new or used battery can cause severe
internal burns and lead to death in as little as 2 hours if
swallowed or enters the body. Always secure the battery
cover. If it does not close securely, stop using the device,
remove the batteries, and keep it away from children. If you
think batteries may have been swallowed or entered the
body, seek immediate medical attention.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” ful
fi
lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/53/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-11:2016+A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 62479:2010
EN 300 328 V2.2.2
EN 301 489-1 V2.2.3
EN 301 489-17 V3.2.4
EN IEC 63000:2018
Winnenden, 2021-02-23
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” ful
fi
lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2017/1206
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016+A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 62479:2010
EN 300 328 V2.2.2
EN 301 489-1 V2.2.3
EN 301 489-17 V3.2.4
BS EN IEC 63000:2018
Winnenden, 2021-02-23
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It can cut
straight lines, curves, and internal cut-outs. It cuts pipes
and can cut
fl
ush to a surface.
Do not use this product in any other way as stated for
normal use.
SELECTING MODE
Allow the tool to come to a complete stop before changing
modes. Press the selector button to cycle between the
settings. Select wireless
to change the default settings
via the ONE-KEY App on your smart device.
Cut brake
stop the Sawzall from cutting, once it fully
cut through the workpiece.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool,
please reference the Quick Start guide included with this
product or go to www.milwaukeetool.com/one-Key. To
download the ONE-KEY app, visit the App Store or Google
Play from your smart device.
When the product experiences ESD, the speed LED shuts
down and the product cannot adjust speed. It needs the
battery and coin cell removed and reinserted to recover
(see page 6 & 16).
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset
manually to recover.
ENGLISH
WARNING Read all safety warnings, instructions,
illustrations and speci
fi
cations provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock,
fi
re and/or serious injury.
Save
all warnings and instructions for future reference.
SABRE SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory
contacting a „live“ wire may make exposed metal parts of
the power tool „live“ and could give the operator an electric
shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the
work by your hand or against the body leaves it unstable
and may lead to loss of control
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device o
ff
immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
*1 with saw blade bimetal, dimension 150 x 1,25 mm and tooth pitch 5 mm
*2 with saw blade bimetal, dimension 230 x 1,6 mm and tooth pitch 5 mm The Ax
TM
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
di
ff
erent applications, with di
ff
erent accessories or poorly maintained, the vibration and noise emission may di
ff
er. This may
signi
fi
cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is
switched o
ff
or when it is running but not actually doing the job. This may signi
fi
cantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the e
ff
ects of vibration and/or noise such as: maintain the
tool and the accessories, keep the hands warm, organization of work patterns.
TECHNICAL DATA CORDLESS RECIPROCATING SAW
Production code.....................................................................
Cutting depth max. in:
Soft- wood
..........................................................................
Steel
...................................................................................
Aluminium
...........................................................................
Non-ferrous metal
...............................................................
Metal pipe
...........................................................................
Stroke rate ............................................................................
Lengths of stroke ...................................................................
Battery voltage.......................................................................
Bluetooth version ...................................................................
Frequency band.....................................................................
Radio-frequency power .........................................................
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah) .....
Recommended ambient operating temperature ....................
Recommended battery types.................................................
Recommended charger .........................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))....................
Sound power level (Uncertainty K=3dB(A)) ........................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Cutting particleboard *1 ......................................................
Uncertainty K=
....................................................................
Cutting wooden beams *2 ..................................................
Uncertainty K=
....................................................................
