Milnor MWF125J7 Manual Download Page 21 | Manualshive

Page: 21 / 112

Milnor MWF125J7 Manual Download Page 21

Pellerin Milnor Corporation

B2T2001013: Hot water connection.

B2T2001014: Cold water connection.

B2T2001015: Reuse (third) water connection. (Optional)

B2T2001016: Flushing water connection. This is the water that
goes into the supply compartment or pumped chemical manifold
to flush chemicals into the machine.

B2T2001028: Look for tags inside the machine. These tags may
identify shipping restraints to be removed or components to be in-
stalled. Do not start the machine until these actions are completed.

B2T2002013: Do not start the machine until shipping restraints
are removed. This tag will appear on the outside of the machine to
alert you to the presence of internal shipping restraints. A tag will
also appear on the restraint to help identify it. Most, but not all
shipping restraints display the color red. Some shipping restraints
are also safety stands. Do not discard these.

B2T2003001: Hold the side of the connection stationary with a
wrench as you tighten the connection with another wrench. Other-
wise, you may twist components, such as valves, damaging them.

Installation Tag Guidelines

17

«
...
19
20
21
22
23
...
»

Summary of Contents for MWF125J7

















































































































Reviews:

No comments