background image

OM-269631 Page 14

4-4. Environmental Specifications

A. IP Rating

IP Rating

IP23

This equipment is designed for outdoor use. It may be stored, but is not intended to be used for welding outside during precipitation unless

sheltered.

IP23 2014

06

B. Information On Electromagnetic Compatibility (EMC)

!

This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low

voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, due to con-

ducted as well as radiated disturbances.

This equipment complies with IEC61000-3-11 and IEC 61000

3

12 and can be connected to public low-voltage systems provided that the public

low-voltage system impedance Z

max

 at the  point of common coupling is less than 19.6 m

 (or the short

circuit power S

sc

 is greater than 8,348,769

VA). It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary,

that the system impedance complies with the impedance restrictions.

ce-emc 1 2014-07

C. China EEP Hazardous Substance Information

 

China EEP Hazardous Substance Information

Component Name

(

)

(if applicable)

 

Hazardous Substance

Pb

Hg

Cd

Cr6

PBB

苯醚

PBDE

黄铜

铜部

Brass and Copper Parts

X

O

O

O

O

O

Coupling Devices

X

O

O

O

O

O

 !

Switching Devices

O

O

X

O

O

O

"#"#

Cable and Cable

Accessories

X

O

O

O

O

O

$

Batteries

X

O

O

O

O

O

%

&'*SJ/T 11364

,-..

This table is prepared in accordance with China SJ/T 11364.

O:

2

 

5

该部

7 8

9:

85GB/T26572

,

限量要

>?@.

Indicates that the concentration of the Hazardous Substance in all homogeneous materials of the part is below the relevant threshold of China

GB/T 26572.
X:

2

 

AC5

该部

DE8

9:

量超

FGB/T26572

,

限量要

>.

Indicates that the concentration of the Hazardous Substance in at least one homogeneous

 

material of the part is above the relevant threshold of

China GB/T 26572.

                

HIKL

'*SJ/Z11388

,N,.

The EFUP value of this EEP is defined in accordance with China SJ/Z 11388.

EEP_2016

06

D. Temperature Specifications

Operating Temperature Range

Storage Temperature Range

14 to 104 

°

F (

10 to 40

°

C)

4 to 131 

°

F (

20 to 55

°

C)

Temp_2016- 07

Summary of Contents for PipePro XC









































































Reviews: