Miller Electric CE-60T Page 46 Owner'S Manual Download

Page: 46 / 60

A complete Parts List is available at www.MillerWelds.com

OM-242 880 Page 42

7-5. Checking Or Replacing Filter Element (Part No. 227 877)

rEF. 805 211-A

Turn off power, and

disconnect input power plug

from receptacle or turn off

and lockout/tagout line dis-

connect device before

working on unit.

Significant DC voltage can

remain on capacitors after

unit is Off. Check to see that

front panel lights (LEDs)

have stopped flashing and

are off before removing

wrapper.

Remove wrapper from unit (see

Section 7-4).
1

Rear Bezel

Remove rear bezel from unit.
2

Filter Bracket Screws

Remove filter bracket screws. Pull

filter bracket toward front of unit

until gas/air supply fitting is past

rear panel, and swing filter

assembly out to the side to allow

filter cup removal.
3

Filter Base

Filter Element

(Part No. 227877)

Filter Cup

Unscrew filter cup from base.
Remove cup.
Unscrew filter element from base.
Check filter element for dirt and

moisture, and replace if necessary.
Be sure that all parts are clean and

dry.
Reinstall filter element, and secure

filter cup.
Secure filter bracket to rear panel.
Reinstall wrapper and rear bezel.

Tools Needed:

5/16 in.

Summary of Contents for CE-60T





























































Search results

Summary of Contents for CE-60T

Reviews:

Related manuals for CE-60T

Brands by name

Popular brands

Miller Electric CE-60T, Owner'S Manual

Search results

Summary of Contents for CE-60T

Reviews:

Related manuals for CE-60T

Brands by name

Popular brands