Miller Electric CE-60T Page 24 Owner'S Manual Download

Page: 24 / 60

A complete Parts List is available at www.MillerWelds.com

OM-242 880 Page 20

4-14. Connecting 3-Phase Input Power

input2 2008

−

803 766-C / 805 159

NOTICE

−

The Auto-Line circuitry in this

unit automatically adapts the power

source to the primary voltage being ap-

plied. Check input voltage available at site.

This unit can be connected to any input

power between 208 and 575 VAC without

removing cover to relink the power

source.

For Three-Phase Operation

Input Power Cord.

Disconnect Device (switch shown in

the OFF position)

Green Or Green/Yellow Grounding

Conductor

Disconnect Device Grounding

Terminal

Input Conductors (L1, L2 And L3)

Disconnect Device Line Terminals

Connect green or green/yellow grounding

conductor to disconnect device grounding

terminal first.
Connect input conductors L1, L2, and L3

to disconnect device line terminals.
7

Over-Current Protection

Select type and size of over-current

protection using Section 4-11 (fused dis-

connect switch shown).
Close and secure door on disconnect

device. Remove lockout/tagout device,

and place switch in the On position.

= GND/PE Earth Ground

Tools Needed:

Installation must meet all National

and Local Codes

−

have only quali-

fied persons make this installation.

Disconnect and lockout/tagout in-

put power before connecting input

conductors from unit.

Always connect green or green/

yellow conductor to supply

grounding terminal first, and never

to a line terminal.

Summary of Contents for CE-60T





























































Search results

Summary of Contents for CE-60T

Reviews:

Related manuals for CE-60T

Brands by name

Popular brands

Miller Electric CE-60T, Owner'S Manual

Search results

Summary of Contents for CE-60T

Reviews:

Related manuals for CE-60T

Brands by name

Popular brands