background image

 

7

 

 

Step 10:

  S ee Fig ure 9  and  10.   

Place the req uired amount of sand  

inside the p ool area.  Pla ce the 3’ 

angles into the slot in the bottom 

rail as shown in Detail 8A.  Insert 

short le g d own.  Star ting a t th e 

bottom cli p o n the d ownwind si de 

of the p ool,  attach th e u pright  slat 

to the bottom c lip.  Be s ure the 

machine  screw i s t o t he insid e of  

the pool.  Wo rking in a cou nter-

clockwise direction, slide a wall slat 

onto the up right slat.  The slat 

should be h eld abo ut 30  degree s 

from the up right slat whil e slidin g 

together.   Then wh

en  seated, 

rotate the wa ll slat again st the wall 

angle.  The skimmer slat should be 

located between the first two round 

side up right slat s  as you  work 

around the pool.  Do not locate the 

skimmer  under the  patio.  The 

return  slat mus t be located within 

15 panels to the left of the  skimmer 

as you face the pool. 

 

Be careful not to let the wall fall 
over during assembly.  The walls 
must remain plumb.  If the wall falls 
over, disassemble fallen section 
and start again.

 

 

Use figure  11 to determine the 

number of slats ne eded on the  

straight sid e of an oval p ool.  The 

count is from upright slat to upright 

slat.

 

BOTTOM RAIL

ADAPTER

 

2” X 8” X 16” 
PATIO BLOCK

 

STAKE 

12X OVALS – SHORT WALL 
CHANNEL (43 7/16”) 
15X & 18X OVALS – SHORT 
WALL CHANNEL (52 13/16”) 

WALL CHANNEL 

BOTTOM CLIP

LINE 2 

FIGURE 8

L00008E 

STACKING 
PATTERN FOR 
POOR SOIL 

BOTTOM 
RAIL 

3’ ANGLE 

SHORT LEG DOWN 

DETAIL 8A 

A00032 

FIGURE 10 

W00036 

SMOOTH SIDE 
AGAINST LINER 

¼” – 20 SS 
HEX NUT 

¼” – 20 x ¾” SS 
MACHINE SCREW 

UPRIGHT 
SLAT 

FIGURE 9 

W00037

WALL SLAT 

BOTTOM 
CLIP 

WALL ANGLE 

WALL SLAT 
ROTATE INTO 
PLACE 

BOTTOM CLIP 

UPRIGHT 
SLAT 

CONSTRUCTION NUT.

  THIS  NUT 

MUST BE REMOVED AT THE 
BEGINNING OF THE FILLING OF 
THE POOL TO ALLOW FOR 
PROPER EXPANSION. 

Summary of Contents for T3669-80A














Reviews: