background image

 

8

FIGURE 12 

W00038 

FIGURE 13

W00039 

Step 11:

  See Figure 1 2. On the oval midse ctions hold the wall 

slats in place with the 3’ angles as shown 

 

After the pool wall is assembled, check the dimensions of the pool 

to insure that it has not shifted during assembly. 

PAN HEAD 
SCREWS

 

SKIMMER 
THROAT 
GASKET 

SKIMMER 
GASKET 
(CORK)

 

LOW PROFILE / FRONT 
ACCESS SKIMMER

 

WALL 

SKIMMER 
THROAT 
GASKET 

NOTE:  THE SKIMMER THROAT 
GASKET MUST SANDWICH THE WALL.  
I.E.  ONE FLAP OF THE GASKET MUST 
BE ON THE INSIDE OF THE WALL AND 
THE OTHER ON THE OUTSIDE.

 

DETAIL 13A 

W00040

Step 12:

  Se e Figure 13 and Detail 13a.  Install th e skimmer throat gasket to each side of the pool  wall and 

attach the skimmer to the wall as  shown using hardware provided with the ski mmer.  Moun t the skimme r at the 

center with only two (2) pan head screws at this point. Refer to skimmer instruction sheet. 

Step 13:

  See Figures 14. Place the bead receiver on the wall with the ends centered over the uprights.  Tape the 

joints of the bead receiver using fabric tape to protect the liner. 

 

Step 14:

  

Loosen the nuts from the bottom clip / upright slat attachment.  If you are installing a walk 

deck on this pool.  Do Not completely remove the nut from the bolt.  You will need this bolt to 
attach the walk deck posts. 

This allo ws the  wall t o expa nd to   its prope r  shape  when filli ng the  po ol.  

Spread the sand across the entire bottom of the pool.  Moisten and tamp the sand to provide a solid base.  

The sand base must be 2” deep after tamping.  Th e sand should be moistened and troweled to a smooth 

finish.  Create a 6” radius cove along the wall as shown in Figure 15.  This cove must also be tamped solid 

to prevent shifting.  Clean the inside of the wall prior to installing liner. 

 
 

 

WALL SLAT 

3’ ANGLE 

BOTTOM RAIL 

 

 

 

 

  15 x 30

pool size 

  12 x 18

12 x 21

15 x 24    18 x 33

pool size 

A=

34 

42 

46 

 

61 

number of slats

FIGURE 11

W00049

 

Upright Slat 

On the round ends there are 11 slats between the upright slats. Except 

for the 12x18 & 12x21 which have 9 slats between the upright slats. 

TRANSITION 
UPRIGHT 

MUD SILLS 

BOTTOM 
RAIL 

TRANSITION UPRIGHT 

MIDSECTION SLAT COUNT 

Summary of Contents for T3669-80A














Reviews: