background image

Printed in China for GTO Access Systems, LLC.

Copyright

©

 2017 GTO Access Systems, LLC

Document Number:  R26208 REV A (06.07.17)

MM262

ACCESS SYSTEMS, LLC

Mighty Mule® is the retail brand of GTO Access Systems, LLC

3121 Hartsfield Road • Tallahassee, FL 32303

This product meets the requirements of UL325 6th Edition, 2016, the standard for gate 

operator safety.

Installation Manual

Example of finished installation

(installations vary slightly on different types of gates)

 

120 Volt indoor

Transformer

(surge protector 

not supplied)

Horizontal Support

Gate Swings Evenly and Freely

Hung Firmly and Plumb

Post Bracket

Control Box

Fence Post Set in Concrete

Run 1000' (max.) of low

voltage wire to control

box from transformer

(wire not included).           

Power Cable

Gate Bracket

Warning Sign

First Gate Opener

Post Bracket

Second Gate Opener

Gate Bracket

Horizontal Support

PVC conduit (not included)

to run second opener power

cable under driveway.

12 Volt automotive or marine 

type battery in weather proof 

housing (REQUIRED, not included).  

Summary of Contents for MM202 Series









































Reviews: