background image

23

  

MM262 Installation Instructions

Accessory Inputs

1

 SAFETY: 

Typically for use with photo beam device, loop 

   

detector or other non-contact sensors

 

•  Activation of this input while the gate is closing will cause the 

gate to stop and return to the opened position.

 

•  Activation of this input while the gate is opening has no effect. 

(gate will continue to open)

 

•  Activation of this input while gate is idle will prevent gate from 

closing.

 

•  Activation of this input while at open limit will restart the auto 

close time (if enabled).

2

 EXIT: 

 Typically for use with exit loop or wand

 

•  Activation of this input will open the gate if it’s not already at the 

open position.

 

•  Activation of this input while at open limit will restart the auto 

close time (if enabled).

 

•  Activation of this input while gate is idle will prevent gate from 

closing.

3

 CYCLE: 

 Typically for use with doorbell button or hardwired 

   keypad

 

•  Each activation at this input will cycle the operation as follows:

 

 

 

…→ OPEN → STOP → CLOSE → STOP → OPEN → …

4

 EDGE:

 

  Typically for use with contact edge sensor

 

•  Activation of this input while gate is moving will cause it to 

reverse direction for 2 seconds.

 

•  Activation of this input while idle will prevent gate from running.

5

 COM:

  

Common/Negative terminal for accessory devices.

12 Volt Power (Maximum Current: 100 mA)

5

 COM:

  Common/Negative terminal for accessory power source.

6

  LOCK +:

  Power source for GTO/Mighty Mule accessories, i.e. Gate Opening Sensor [FM138].

Lock Outputs

6

  LOCK +:

  Positive terminal to connect Automatic Gate Lock [FM143].

7

  LOCK – : 

 Negative terminal to connect Automatic Gate Lock.

Charge Power Inputs

8

  CHGR: Power Input Terminals:

 

•  Input terminals for transformer or solar panel.

 

•  Non-polarity sensitive.

VAR5

VAR6

K1

PF1

K2

BATT 

+

BATT 

K3

K4

VAR4

VAR3

VAR2

VAR1

MIN

MAX OFF

JP1

REMOVE JUMPER FOR

PUSH TO OPEN OPTION

120

SEC.

G

TO Inc.   

Tallahassee, FL

R4722

STALL FORCE

OPEN  <  JOG  >  CLOSE

PWR.

SET

LIMIT

1st  OPR.

2nd  OPR.

STATUS

AUTO CLOSE

SFTY.

EXIT

CYCLE

EDGE

SENSOR

COMMON

LOCK+

LOCK–

WHT

GRN

RED

BLK

WHT

GRN

SECOND OPR

.

FIRST OPR

.

RED

BLK

14 VAC

OR   

SOLAR

ON  OFF

1

8

7

6

5

4

3

2

Summary of Contents for MM202 Series









































Reviews: