7
WIRELESS DA-605P DRIVE-ALERT
DA-605P CONTROL PANEL/RECEIVER GENERAL INFORMATION:
The DA-605P Drive-Alert’s receiver board is the same as the one used in the DA-600 receiver (see FIGURES 5-6). However,
the DA-605P does not have an internal whistle, nor a whistle switch. The advantages of the DA-605P over the DA-600 are the
DA-066 wireless chime transmitter which activates remote chimes as an alert. Any combination or quantity of the DA-068 Plug-in
Chimes and/or the DA-070 Battery-powered Portable Chimes may be used. Each chime is activated by a radio signal from the
DA-066 attached to the control panel. (See Accessories page). These chimes have a choice of three tones and volume control,
and can be used up to 100’ away from the control panel. As stated, the DA-068 plugs into any standard wall outlet and can be
easily hidden behind furniture. The DA-070 can be taken into the backyard, out to the pool & etc.
DA-605P Control Panel with one DA-068 Plug-in Remote Chime and a DA-610TO Sensor/Transmitter
(Optional DA-070 Battery Operated Portable Chime pictured on Accessories Page)
TESTING FOR RADIO TRANSMITTER COMMUNICATION
:
The alarm signal is used to turn on the 315 MHz radio signal in the push button located on the top of the DA-605P, which will
sound the remote chime. This signal will reach at least 100 feet to the chime. The radio module located on the top of the housing
contains a user accessible push button for test or “call” purposes. Internal to the module a 12 volt battery type A23 is contained
and should last about 3 years. This battery is activated only when testing the radio module to chime signal path and does not
have an effect on Drive-Alert operation. The chime can be tested independent of the Drive-Alert by pushing the button causing
the chime to sound. The enclosure of the radio module can be opened by pushing in on the bottom latch carefully with a screw-
driver and lifting up. Both the jumpers as well as the battery are now accessible. To re-seat the radio module enclosure carefully
align and place the enclosure top locking tabs and carefully push in the bottom latch until it snaps closed. The DA-068 Plug-in
Chimes and DA-070 Battery-powered Portable Chimes are factory preset for an 8 note Westminster tone. To change the sound
to a two note tone, remove jumper #8 under the small cover on the back of the chime, To obtain a 1 note tone, remove only the
jumper from the radio module while leaving the jumper in the chime.
INSTALLATION
:
For Sensor/Transmitter installation details see the sensor installation pages. The DA-068 & DA-070 chimes may be located in
multiple rooms and locations and the DA-605P can chime an unlimited number of chimes within 100+ feet of the Control Panel.
Simply plug the Control Panel in a standard wall outlet, in an out of site space where the signal from the DA-610 Sensor can
reach it. Plug in the DA-068 Remote Chime(s) and place the DA-070 Portable Chimes in an area(s) of the house where an alert
is desired. The DA-068 volume control is accessible on the back panel of the chime. However, the DA-070 must have its back
removed to gain access to the volume control. The DA-070 Battery Operated Portable Chime needs three D size batteries which
will last about 3 years. For all options and operation instructions of the chimes, see the instructions enclosed with the chimes.
Figure 5 shows a typical DA-605P control panel connection to a “line of sight wireless transmitter” like our DA-606LK Light Kit
FIGURE 5
For DA-605P control panel and DA-610TO/DA-611TO sensor specifications, see previous page 6.
DA-605P to a DA-606LK
Black Red Green
Blue “jumper”
SIG ALA +5VDC GND
+24DC
NO NC C NO C
UN REG
If your Drive-Alert does not
look like this, you may have
an older model. Please call
Mier’s free tech support line
at 800-473-0213
If your Drive-Alert does not
look like this, you may have
an older model. Please call
Mier’s free tech support line
at 800-473-0213
