Mier Drive Alert DA-600 Installation Manual Download Page 7

6

WIRELESS DA-600 

PAGE 3 OF 3

DA-600, DA-605P, DA-610TO & DA-611TO SPECS

Figure 4 shows a typical DA-600 control panel connection to a “line of sight wireless transmitter” like our DA-066, with the whistle
ON or OFF

FIGURE 4

SPECIFICATIONS

:

DA-600 and DA-605P CONTROL PANEL/RECEIVER:

1. 

INPUT POWER:   

120 VOLTS AC 50-60 HZ, 3 WATTS

2. 

OUTPUT POWER:  

24 VOLTS DC AT 100 MILLIAMPERES (.1 AMP)

3. 

FREQUENCY:  

433.92 MHZ FIXED SUPERHETRODYNE

4. 

ANTENNA:  

¼ WAVE MONOPOLE FIXED BOLTED IN STEEL CASE 0 DBI GAIN

5. 

RECEIVER:  

LINX TECHNOLOGIES MODEL KH2

6. 

ADDRESS CODES: 

FOUR POSITION DIP SWITCH

7. 

LAMPS/LEDS:  

POWER=RED, LO BATT=YELLOW, VALID XMSN=RED, ALARM=RED

8. 

OUTPUT:  

PIEZO WHISTLE AND 24 VOLT RELAY

9.

ALARM TIME:  

ADJUSTABLE 2 TO 12 SECONDS FOR EACH ALARM.

10.

OPERATING TEMP: 

0 DEGREE F. TO +105 DEGREE F.  

11. 

WEIGHT:  

2.5 POUNDS.

DA-610TO SENSOR/TRANSMITTER:

1. 

POWER REQUIREMENTS:  

TWO (2) SIZE AA (LR-6) BATTERIES  3.0 VOLTS DC

2. 

OPERATING FREQUENCY:  

433.92 MHZ FIXED

3. 

ANTENNA:    

 

1/4 WAVE MONOPOLE BOLTED INTO THE STEEL CASE.  0 DBI GAIN

4. 

TRANSMITTER OUTPUT:  

2  MILLIWATTS

5. 

TRANSMITTER:  

LINX TECHNOLOGIES MODEL KH ENCODER/TRANSMITTER

6. 

ENCODER MODULATION:  

AMPLITUDE ON-OFF KEYING (OOK) AT 1200 BPS.

7. 

ADDRESS CODES:  

FOUR POSITION DIP SWITCH SELECTED FOR THE ENCODER

8. 

DATA:   

   ONE DATA BIT ENCODED WHEN BATTERY IS LOW.

9.

TRANSMITTER ON TIME: 

LESS THAN 5 SECONDS FOR ANY SINGLE ALARM

10. 

ENCLOSURE:    

 

18 GAUGE GALVANEAL PAINTED STEEL WITH WEATHER SEAL AND  LOCKABLE 
LATCH CLOSURE. HOUSES THE TRANSMITTER AND SENSOR

11. 

QUIESCENT CURRENT :   

60 MICROAMP

12. 

ACTIVE CURRENT:   

3 MILLIAMP

13. 

BATTERY LIFE:  

ABOUT ONE YEAR IN RESIDENTIAL USE.

14.

OPERATING TEMP:

-40 DEGREES F TO + 125 DEGREES F

15. 

WEIGHT:    

 

FOUR POUNDS

16. 

DETECTION OF VEHICLES: 

DISTANCE FROM SENSOR/TRANSMITTER UNIT FOR STANDARD SEDAN MOVING 
AT 5 MPH+ IS 14 FEET (MAX), 9 FEET (MID), 7 FEET (MIN)

DA-611TO SENSOR/TRANSMITTER:

ALL SPECIFICATIONS ARE THE SAME AS THOSE LISTED FOR THE DA-610TO ABOVE, EXCEPT THE FOLLOWING:
A. 

THE SENSOR IS NOT INSIDE THE ENCLOSURE WITH THE TRANSMITTER.  IT IS AN EXTERNAL SENSOR 

 

ATTACHED TO THE TRANSMITTER ENCLOSURE WITH 50’ OF CABLE (SEE OPTIONS PAGE)

B. 

DETECTION OF VEHICLES: 

DISTANCE FROM SENSOR/ FOR STANDARD SEDAN MOVING AT 5 MPH+ IS
17 FEET (MAX), 12 FEET (MID), 10 FEET (MIN)

If your Drive-Alert does not 
look like this, you may have 
an older model.  Please call 
Mier’s free tech support line 
at 800-473-0213

DA-600 with WHISTLE ON or OFF

   SIG    ALA  +5VDC  GND 

+24DC

    NO     NC       C        NO       C

UN REG

Red wire to “NO”
Black wire to “C”

DA-066 Push-Button Wireless 
Chime Transmitter

Red 

         Black

Summary of Contents for Drive Alert DA-600

















Reviews: