Miele WXF 660 Operating Instructions Manual Download Page 66

Page: 66 / 104

Frequently Asked Questions

Messages or faults affecting the TwinDos system

Problem

Possible cause and solution

No detergent was
dispensed during
washing.

TwinDos is deactivated.



Before the next wash program, ensure that the

TwinDos

sensor button is lit.

Detergent is not dispensed even though the

TwinDos

sensor button is lit.



Try again.



If detergent is still not dispensed, contact Miele
Service.

A new detergent
cartridge has been
inserted, but the
cartridge is identified as
empty when the
machine is switched on.

The washing machine was switched off when the
detergent cartridge was replaced.



Switch on the washing machine.



Remove the detergent cartridge and then reinsert
it into the compartment.

The counter is set to 0.

Summary of Contents for WXF 660









































































































Search results

Summary of Contents for WXF 660

Reviews:

Related manuals for WXF 660

Brands by name

Popular brands

Miele WXF 660, Operating Instructions Manual

Search results

Summary of Contents for WXF 660

Reviews:

Related manuals for WXF 660

Brands by name

Popular brands