background image

Delayed Start

W

Use the

W

"Delay start" button to program

the unit to start automatically at a later time.

^

Turn the key to position

B

"Operation".

^

Turn on the machine and select the requi-
red program with the program selector.

The display shows the following (example):

PROGRAMME

1

COTTONS

>95 °C<

Main wash

1

Rinses

3

1000 RPM

^

Press

W

"Delay start".

Here the display shows the following:

PROGRAMME 1

COTTONS

Start time

>14< : 30

hrs

After the time has been set

press the Start button

The current time of day (military time) is al-
ways displayed first.
The cursor points to the input field for
‘hours’.

^

Select the start time with

3 4

"Minus or

Plus" buttons.

^

Position the cursor on the input field for mi-
nutes and select the minutes with

3 4

"Minus or Plus".

Before pressing the

X

"Start" button the

start time can be deleted by pressing
again on the

W

"Delay start" button, or by

turning the machine off and then on
again.

^

Press

X

"Start" to confirm the delayed

start, and the following will appear in the
display:

PROGRAMME

1

COTTONS

95 °C

Main wash

1

Start time

18 : 30 hrs

When the start time is reached the program
begins and the display shows the program
sequence. If

W

"Delay start" is pressed du-

ring the program, the actual time of day and
date are shown.

If

7

"End" is pressed the delay start function

will be cancelled.

Operation

16

Summary of Contents for WS 5101

































Reviews: