Miele WMB 120 Operating Instructions Manual Download Page 28

Page: 28 / 84

Spinning

Final spin speed

Programme

rpm

Cottons

1600

Minimum iron

1200

Woollens



1200*

Outerwear

800

Proofing

1000

Delicates

900

Express 20

1200

Dark garments / Denim

1200

Shirts

900

Drain / Spin

1600

Final spin speed in the
programme

When a programme is selected the
optimum spin speed for that
programme will appear in the display.
For programmes marked with a

in the

chart, the optimum spin speed is not
the maximum spin speed.

You can reduce the final spin speed.

However, you cannot select a final spin
speed higher than that shown in the
chart.

Rinse and interim spin

There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the
interim spin speed. If a spin speed of
less than 700 rpm is selected for the

Cottons

programme, an additional rinse

is introduced.

Summary of Contents for WMB 120





















































































Search results

Summary of Contents for WMB 120

Reviews:

Related manuals for WMB 120

Brands by name

Popular brands

Miele WMB 120, Operating Instructions Manual

Search results

Summary of Contents for WMB 120

Reviews:

Related manuals for WMB 120

Brands by name

Popular brands