Miele WMB 120 Operating Instructions Manual Download Page 72

Page: 72 / 84

Settings

You can use the settings menu to alter
the machine's electronics to suit
changing requirements.

Settings can be altered at any time.

To access Settings

Before you begin, ensure that:

– The washing machine is switched on.

– The standard display is showing.







2:59



1600



Touch the



and



sensors at the

same time.

Language 



You are now in the Settings menu.

Changing a setting



Touching the



sensor will call up the

different options for the setting.

The option which is selected will have
a tick



next to it.



When the option you want shows in
the display touch the

sensor to

activate it.

Exiting a setting



Touch the





sensor repeatedly

until

Back 

appears in the display.



Touch the

sensor.

Summary of Contents for WMB 120





















































































Search results

Summary of Contents for WMB 120

Reviews:

Related manuals for WMB 120

Brands by name

Popular brands

Miele WMB 120, Operating Instructions Manual

Search results

Summary of Contents for WMB 120

Reviews:

Related manuals for WMB 120

Brands by name

Popular brands