Miele WDA 210 WPM Operating Instructions Manual Download Page 42

Page: 42 / 72

Problem solving guide

Problem

Possible cause and remedy

The

Check inlet

fault in‐

dicator light flashes and

a fault number appears

in the display.

The water inlet is blocked.



Turn on the tap.

The filter in the water inlet hose is dirty.



Clean the filter.

The

Check inlet

and

Check drainage

fault in‐

dicator lights flash and

a fault number appears

in the display.

The water protection system has reacted.



Turn off the tap.



Call Miele.

The

Soak/Pre-wash

Rinses

indicator lights

flash in the programme

sequence display and a

fault number appears in

the display.

There is a fault.



Start the programme again. If the fault message

appears again, contact Miele.

To switch off the fault indicator: Switch the washing machine off with the



button

and turn the programme selector to

Finish

Summary of Contents for WDA 210 WPM









































































Search results

Summary of Contents for WDA 210 WPM

Reviews:

Related manuals for WDA 210 WPM

Brands by name

Popular brands

Miele WDA 210 WPM, Operating Instructions Manual

Search results

Summary of Contents for WDA 210 WPM

Reviews:

Related manuals for WDA 210 WPM

Brands by name

Popular brands