Miele wda 201 Operating Instructions Manual Download Page 46

Page: 46 / 72

Problem solving guide

The door will not open

Problem

Cause and remedy

The drum door cannot
be opened by pressing
the

Door

button.

The washing machine is not connected to the elec-
trical supply and / or is not switched on.



Insert the plug in the socket and switch on and / or
switch the machine on with the



button.

Power cut.



Open the door as described in “Opening the door
in the event of blocked drain outlet and/or power
failure”.

The door was not correctly engaged.



Press hard against the lock side of the door and
then press the

Door

button.

There is still water in the drum and the machine is un-
able to drain.



Clean the drain filters and the drain pump.

For safety reasons the door cannot be opened if the
suds temperature is higher than 55°C.



Allow the programme to finish or cancel it and wait
until the temperature in the drum has dropped.

Summary of Contents for wda 201









































































Search results

Summary of Contents for wda 201

Reviews:

Related manuals for wda 201

Brands by name

Popular brands

Miele wda 201, Operating Instructions Manual

Search results

Summary of Contents for wda 201

Reviews:

Related manuals for wda 201

Brands by name

Popular brands