Miele wda 201 Operating Instructions Manual Download Page 40

Page: 40 / 72

Cleaning and care

Cleaning the water inlet filter

The washing machine has a filter to pro-
tect the inlet valve.

The filter in the union in the open end of
the inlet hose should be replaced every
6 months or so, or more often if there
are frequent interruptions to the water
supply.



First turn off the stopcock.



Unscrew the inlet hose from the stop-
cock.



Remove the rubber seal

from the

union.



Hold the free end of the inlet hose
downwards. Plastic filter

will drop

out.



Clean the plastic filter.



Put the filter and seal back in the re-
verse order and reconnect the hose.



Turn on the stopcock and check the
connection is watertight. If water
drips out, tighten the connection.

The filter

must

be put back in place

after cleaning.

Summary of Contents for wda 201









































































Search results

Summary of Contents for wda 201

Reviews:

Related manuals for wda 201

Brands by name

Popular brands

Miele wda 201, Operating Instructions Manual

Search results

Summary of Contents for wda 201

Reviews:

Related manuals for wda 201

Brands by name

Popular brands