Miele W 4144 WPS Operating Instructions Manual Download | Manualshive

Page: 30 / 68

background image

The right amount to dispense will
depend on the following:

– The quantity of laundry

– The soiling level of the laundry

Lightly soiled
No visible dirt or stains. Possibly
slight body odour.

Normally soiled
Visibly dirty and/or just a few slight
stains.

Heavily soiled
Visible dirt and stains and/or dried on
soiling.

– The water hardness level.

Check with your local water supplier
if you do not know the hardness level
in your area.

Water softener

A water softener can be used to cut
down on the use of detergents in hard
water areas. Dispense according to the
amount specified on the packaging.
First add detergent and then the water
softener.

Miele branded water softening tablets
are available from the Miele Spare Parts
Department or via the internet on
www.miele-shop.com.

Use a quantity of detergent as for soft
water.

Miele do not recommend connecting
the machine to a household water
softener.

Washing with several
components

If you wash using several components
(e.g. special application detergents),
we recommend always dispensing the
agents into compartment

j

in the

following order:

1. Detergent

2. Water softeners

3. Stain remover

This way the agents are distributed
more evenly.

Detergent

30

«
...
28
29
30
31
32
...
»

Summary of Contents for W 4144 WPS





































































Reviews:

No comments

Related manuals for W 4144 WPS

Brand: Haier Pages: 20

Brand: GE Pages: 24

Brand: Kärcher Pages: 196

Brand: Kärcher Pages: 65

Brand: Kärcher Pages: 20

Brand: Kärcher Pages: 208

HD 4.5/32-4 S Eb HD 4.5/32-4 S Ec

Brand: Kärcher Pages: 36

Brand: Kärcher Pages: 44

Brand: Kärcher Pages: 264

Brand: Samsung Pages: 38

Brand: Samsung Pages: 84

Brand: Samsung Pages: 10

Martha Stewart MTS-1450PW

Brand: SNOWJOE Pages: 16

FDW-VRR606BDE++

Brand: FRAM Pages: 42

Brand: GE Pages: 72

Brand: FULLER O’BRIEN Pages: 28

Brand: Kärcher Pages: 232

Brand: Sears Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands