Miele W 4144 WPS Operating Instructions Manual Download Page 27

Page: 27 / 68

Cancelling a programme

You can cancel a programme at any
time after it has started.

Press the

Start/Stop

button.

Cancel programme

Press the flashing

Start/Stop

button

again.

The suds will be pumped away.

If you want to remove the laundry:

Press the

Door

button.

If you want to select a different
programme:

Switch the machine off with the

I-On/0-Off

button.

Switch the washing machine back on
again.

Check that there is still detergent in
the detergent drawer. Add detergent,
if necessary.

Select and start a new programme.

Interrupting a programme

Switch the machine off with the

I-On/0-Off

button.

To continue with the same programme:

Switch the machine back on with the

I-On/0-Off

button.

Changing a programme

After the start of a programme it is no
longer possible to select a different
programme.

Temperature

It is possible to select a different
temperature up to 5 minutes after the
programme has started.

Press the

Temperature

button.

Spin speed

It is possible to change the spin speed
up until the final spin begins.

Press the

Spin speed

button.

Extra options

It is possible to select or deselect the

Short

and

Water plus

extra options up

to five minutes after the programme has
started.

A programme cannot be cancelled
or changed if the safety lock has
been activated.

Changing the programme sequence

Summary of Contents for W 4144 WPS





































































Search results

Summary of Contents for W 4144 WPS

Reviews:

Related manuals for W 4144 WPS

Brands by name

Popular brands

Miele W 4144 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 4144 WPS

Reviews:

Related manuals for W 4144 WPS

Brands by name

Popular brands