Miele W 3831 WPS Operating Instructions Manual Download | Manualshive

Page: 30 / 68

background image

The right amount to dispense will
depend on the following:

– The quantity of laundry.

– The soiling level of the laundry.

Lightly soiled
No visible dirt or stains. Possibly
slight body odour.

Normally soiled
Visibly dirty and/or just a few slight
stains.

Heavily soiled
Stains and soiling clearly visible.

– The water hardness level.

– Check with your local water supplier

if you do not know the water
hardness level in your area.

Water softeners

A water softener can be used to cut
down on the use of detergents in hard
water areas. Dispense according to the
amount specified on the packaging.
First add detergent and then the water
softener.

Use a quantity of detergent as for soft
water.

Washing with several
components

If you wash using several components
(e.g. special application detergents),
dispense them into compartment

j

in

the following order:

1. Detergent

2. Water softener

3. Stain remover

This way the agents are distributed
more efficiently.

Detergent

30

«
...
28
29
30
31
32
...
»

Summary of Contents for W 3831 WPS





































































Reviews:

No comments

Related manuals for W 3831 WPS

K 3 Premium Power Control

Brand: Kärcher Pages: 16

K 3 Premium Power Control

Brand: Kärcher Pages: 40

Brand: Hanseatic Pages: 72

Brand: Hoover Pages: 144

Brand: N'DUSTRIO Pages: 27

Brand: Jenn-Air Pages: 14

Daema DWF-1101Q

Brand: DAEWOO ELECTRONICS Pages: 17

Brand: Philco Pages: 192

Brand: AEG Electrolux Pages: 36

Brand: arcelik Pages: 24

ProWash P1000 HOT

Brand: Target Pages: 26

Brand: Dual Pumps Pages: 20

Brand: Miele professional Pages: 140

Speed Queen AWM190

Brand: Raytheon Pages: 86

Brand: Merloni Pages: 14

Brand: Lett Pages: 97

Brand: Daewoo Pages: 9

Brand: Haier Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands