Miele W 3831 WPS Operating Instructions Manual Download

Page: 61 / 68

Suds cooling in the Cottons
programme

When this is activated, additional
water flows into the drum at the end
of the main wash to cool the suds
down. Hot suds can damage plastic
drainage pipes.

Suds cooling takes place when
temperatures of 95°C and 75°C are
selected.

Suds cooling should be activated:

– to prevent the danger of scalding if

the drain hose is hooked over the
edge of a sink or basin.

– where the drainage pipes do not

comply with DIN 1986.

The washing machine is delivered with
Suds cooling for the

Cottons

programme deactivated.

Follow steps

to programme

and store in memory.

Before you begin, first ensure that:

– The washing machine is switched off.

– The drum door is properly closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button twice.

– The

Buzzer

indicator light will flash

three times.

will flash in the display alternating

with the number

= Suds cooling is

deactivated

= Suds cooling is

activated

Press the

Start/Stop

button to

change the display from

from

Switch the machine off with the

I-On/

0-Off

button.

The setting you have selected is now
stored in memory and will remain so
until you alter it.

Programmable functions

Summary of Contents for W 3831 WPS





































































Search results

Summary of Contents for W 3831 WPS

Reviews:

Related manuals for W 3831 WPS

Brands by name

Popular brands

Miele W 3831 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 3831 WPS

Reviews:

Related manuals for W 3831 WPS

Brands by name

Popular brands