Miele TKB 550 WP Operating Instructions Manual Download Page 35

Page: 35 / 72

Cleaning and care

Cleaning the fluff filters and air flow
openings thoroughly

If the drying duration has become
longer or the surface of the filters is
visibly compacted with fluff, you
should carry out the following
cleaning procedure.



If using a fragrance flacon make

sure you remove it beforehand.



Pull the upper fluff filter forwards to
remove it.



Turn the yellow dial on the lower fluff
filter in the direction of the arrow (until
you hear it click).



Hold the dial and pull the fluff filter
forwards to remove it.



Use a vacuum cleaner with a long
crevice nozzle attached to remove
any visible fluff from the upper air
flow openings.

Cleaning the fluff filters with water



Flush the fluff filters through with hot
running water.



Shake the fluff filters thoroughly and
then dry them carefully.



Ensure the filters are dry before

replacing them. Wet filters could
cause operational faults.



Push the lower fluff filter in
completely and lock it with the yellow
dial.



Push the upper fluff filter in
completely.



Close the door.

Summary of Contents for TKB 550 WP









































































Search results

Summary of Contents for TKB 550 WP

Reviews:

Related manuals for TKB 550 WP

Brands by name

Popular brands

Miele TKB 550 WP, Operating Instructions Manual

Search results

Summary of Contents for TKB 550 WP

Reviews:

Related manuals for TKB 550 WP

Brands by name

Popular brands