Miele TKB 550 WP Operating Instructions Manual Download Page 48

Page: 48 / 72

What to do if ...

Problem

Cause and remedy

A programme does not
start

No obvious cause.



Connect the tumble dryer to the mains



Turn on the tumble dryer



Close the door



Check whether the mains fuse has tripped

Has there been a power cut? When power is restored
any previously running programme will restart
automatically.

The display is dark and
the

Start/Stop

button is

flashing slowly

The dryer is in standby mode. This is quite normal
and does not indicate a fault.



See "Programmable functions -



Standby".

The drum will turn at intervals in the anti-crease
phase.

The dryer is switched
off at the end of the
programme

The dryer switched off automatically. This is quite
normal and does not indicate a fault.



See "Programmable functions -



Automatic

switch-off".

The interior drum
lighting does not come
on

The drum lighting will switch off automatically ...
... when the door is closed.
... after a few minutes when the door is open (to save
energy).
If the dryer is switched on, the drum lighting will
come on when the door is opened.

Summary of Contents for TKB 550 WP









































































Search results

Summary of Contents for TKB 550 WP

Reviews:

Related manuals for TKB 550 WP

Brands by name

Popular brands

Miele TKB 550 WP, Operating Instructions Manual

Search results

Summary of Contents for TKB 550 WP

Reviews:

Related manuals for TKB 550 WP

Brands by name

Popular brands