Miele PT 7188 Operating And Installation Instructions Download Page 55

Page: 55 / 60

Venting system with flexible
ducting

Flexible ducting can be fitted using
an adapter.

The following items are required:

– an adapter.

– flexible ducting hose*

– a wall vent kit* or window vent kit*.

(* optional accessory)

Fit the adapter (1) and flexible
ducting hose* (2), as shown.

Example: Connection to an exhaust flue

The exhaust air must not be

vented into a chimney or vent flue
which is in use, nor should it be
connected to ducting which
ventilates rooms with fireplaces.

1. Pipe with connection piece

(= supplied with wall vent kit)

2. Adapter for flexible ducting hose

3. Exhaust flue insulated against damp

Example: Window vent

1. Window vent kit (fitted in a

"plexiglass" pane)
(separate fitting instructions are
supplied with the Miele window vent
kit)

2. Adapter for flexible ducting hose

Installation - extraction ducting

Summary of Contents for PT 7188





























































Search results

Summary of Contents for PT 7188

Reviews:

Brands by name

Popular brands

Miele PT 7188, Operating And Installation Instructions

Search results

Summary of Contents for PT 7188

Reviews:

Brands by name

Popular brands