manualshive.com logo in svg

Miele PT 7188, Operating And Installation Instructions

Share
Download
Miele PT 7188 Operating And Installation Instructions Download Page 12

~

In many programmes, the heating phase is followed by a cooling

down phase to ensure that the items are not too hot to handle when
you remove them (this also avoids the danger of the laundry
self-igniting). The programme is not finished until the cooling down
phase has been completed.
Ensure that you always wait until the end of the programme before
removing the laundry.

~

Warning

: Do not switch the appliance off before the end of the

drying programme. If this was done and the laundry was then
removed immediately it could give off a great amount of heat.

~

Fabric conditioner and similar products must be used according

to the instructions on the manufacturer's packaging.

~

The tumble dryer is not to be used if industrial chemicals have

been used to clean it.

~

For appliances with ventilation openings in the base, a carpet

must not obstruct the openings.

~

The tumble dryer must not be used

– without the fluff filters in place or if the fluff filters are damaged.

– without the fine filter in place or if the fine filters are damaged.

This would cause an excessive build-up of fluff which in turn would
cause a fault!

~

After every cycle, remove the fluff from the surfaces and the fluff

filters (see "Cleaning and care").

~

Fluff must not be allowed to accumulate around the tumble dryer.

~

The fluff filters and the fine filter must be thoroughly dried after

cleaning. Damp or wet filters could cause operational faults.

Warning and Safety instructions

12

Summary of Contents for PT 7188





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands