manualshive.com logo in svg

Miele PT 7188, Operating And Installation Instructions

Share
Download
Miele PT 7188 Operating And Installation Instructions Download Page 15

~

Benzine, petrol, paraffin or any easily flammable liquid must not

be stored or used near the tumble dryer stack. Fire and explosion
risk.

~

Do not allow air contaminated with chlorine, fluorine or other

vapours containing solvents to get into the tumble dryer stack. Fire
hazard.

~

For appliances with stainless steel surfaces:

The stainless steel surfaces must not come into contact with liquid
cleaning and disinfecting agents which contain chlorine or sodium
hypochlorite. These agents can have a corrosive effect on stainless
steel.

Aggressive vapours containing chlorine can also be corrosive.
Do not store containers of these agents near the appliance.

Accessories

~

Only use genuine Miele original spare parts and accessories with

this appliance. If spare parts or accessories from other
manufacturers are used, this will invalidate the warranty, and Miele
cannot accept liability.

Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.

Warning and Safety instructions

15

Summary of Contents for PT 7188





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands